Search:

I went to one of the classes on this unit and thought it would be a good fit for this job. 18 seer, 2-3 ton...capable of ramping up to 3.5 tons and slowing down to 1.5 tons.


Sent from my iPad...

Coil drains on the left side into a condensate pump. I don't mind the ragging on my install. Homeowner was happy and it passed inspection. There are quiet a few things that could have been done...

Can I use another kind of media filter in the Perfect Fit model BAYFTAHEXM2 housing? Like with the Spaceguard housing, you can use the regular media filters and they fit snug.

Everybody does things differently. It's not an improper install. Everything is done by code. Yes there are things that could be done differently, thus the reason I posted the pictures. I'm here to...

It's set to run gas at 40. It' is an Ecotemp sold by Gemaire. It has a Mitsibishi compressor.

The flue pipes do have primer on them. The filters are in the filter grills upstairs. This basement is large enough that piping the intake out was not needed. We should have hard piped it out the...

The return box is smaller. It is still the same size opening for the furnace. The electrician reconnected the electrical. The outdoor unit is a Monarch Ecotemp from Gemaire.


Sent from my iPad...

18 seer variable speed heat pump with 95% gas furnace. It was set up as a dual fuel through the thermostat. We used Honeywell 8000 red link with wireless outdoor sensor, wireless indoor sensor for...

I think it looks very clean. If the drain line clogged and filled the cabinet, could the water run down the return where the filter is being the return box is mounted directly and the pan is butted...

I would verify the piston size. Suction pressure is a little high unless the return temp is high also.


Sent from my iPad using Tapatalk

About forgot I had this. It was sitting in the back seat of one of my trucks that has a bad fuel pump. I have just now gotten around to fixing the truck and found it still in there. I have posted it...

I have the Dewalt 20v kit with the impact and drill and really like it. I would like to get a rotary hammer.

I just purchased a Ridgid from Home Depot for $79. I have played with it around the house and it does pretty well.

I purchased this about 2 months ago and used it for a week. I decided to just use my tablet instead. It mounts under the seat lugs so no drilling needed. I paid $300 plus shipping...would take $200...

Might could sell them a quarterly maintenance contract if that fixes the problem.

I would clean the coil. I have seen things like hair products coat the coil and not allow water to follow the fins down to the pan. It may look clean but I bet there is something coating it.

I have an older Testo 506 that I used for the last several years and until recently started to flash from 10.5IWC to 1.4 or so. I picked up the Fieldpiece SDMN5 and really like it. I have used it...

I would remove refrigerant to get the superheat where I wanted it and see what the pressures are then.

Looks great...might be a stupid question but how did you go about sizing the return with the pipe going through it?

I purchased one last week after someone stole a jug of R-22 that was full and an almost empty jug of 410 along with my Fieldpiece IR leak detector that I paid an arm and a leg for. I think I paid...

I just did one using this.... http://www.harborfreight.com/power-tools/oscillating-tools/oscillating-multifunction-power-tool-60428.html
It will wear down the blade very fast but don't throw it...

I would take one of the study prep seminars. If you can familiarize yourself with which books the questions are in and are able to find them quickly, you really don't have to answer any of the load...

456281456291456301

This unit is in the break room for smokers


Sent from my iPhone using Tapatalk

They never mentioned it tripping the roll outs. It was rolling out just enough that the flame was coming up between the furnace cabinet and the top of the burner box. They didn't know it until it...

There were 2 holes that were about 1/8" wide. I don't think it was ever serviced. They called because when it lit and the blower came on, the flame would roll out enough that it burnt the wires going...

This was a 125000btu furnace. Load calculation calls for 75000. Just installed a 95% 80000btu 2 stage Goodman.


Sent from my iPhone using Tapatalk

456181456191456201



Sent from my iPhone using Tapatalk

Would hate to see the head pressure on that last one


Sent from my iPhone using Tapatalk

These we're taken in the parking deck of a motel at the beach.

455011455021

Also found oil nozzles, and igniters for furnaces on their website

Just seen that Home Depot now has a listing for Gas Furnace Control Boards.

http://www.homedepot.com/p/Unbranded-5-1-2-in-Lennox-Furnace-Control-Board-ICM289/204103783#.Upnxa9JDuSo


What will...

You could use something like this http://www.totalairsupply.com/files/Nordyne_Dual_Fuel_Kit.pdf

Or use something like the PRO 8000 or an equivalent thermostat that has the capabilities to do it.

"Duel Fuel" is also referred to as a hybrid system. It consists of a gas furnace and a heat pump instead of the ac that is normally standard with gas. So instead of a air handler with heat strips as...

Yeah, it does pressure just fine, just not pulling through the high side. I'll give them a ring Tuesday being that Monday is a holiday.

I've had my set for a while now. I was using them the other day and noticed when pulling a vacuum through them with both sides open, it will only pull through the low side. The high side will not...

I have sold this, sorry for not posting it being sold.

I've had 3-4 sets of NRP hoses and have never had a problem with them.

Open your low side and high side on your manifold and let it pass through when you remove the hoses. Remove high side first and let the pressure pull back down to normal suction pressure and then...

yes, still metal cabinet AH. I have not checked anything on the heatstrips. I will give them a look in the morning.

The ground wire is connected to the pigtail that plugs into the module. The connector is not cracked anywhere that would let the terminals bleed power over. The power would have to be feeding back...

When I pull up the diagram it looks to be in the right spot.


Sent from my iPad using Tapatalk

I have replaced the module, motor and board all under warranty. It ran once I installed everything and then they called back and was having the same problem. Motor checks OK, board checks OK. I'm...

Am I missing something? I'm still thinking bad module.

It's on an air handler. I checked voltage on the ground wire to a screw on the air handler cabinet. The ground wire is coming back out of the module. When it's unplugged I have 126 on both power...

Hey guys, I got a call late in the day Wednesday with a XL15i being froze up that I installed in 08. When I get there I find that the blower is not running. I don't have the Tec-Mate or Zebra tester...

380881

Make me an offer if anybody is interested and could use it.

Practically brand new. I did put the batteries in it but that's about it. 380871

$75 plus shipping

Got it...that is what I was looking for....Thanks

Could someone point me in the direction of where to look to find info on this unit...much appreciated

It pulled down to 400 before I stopped it when isolated. I have changed the oil 3 times just on this unit. Hooking up inside might be the way to go. I'm going to bring home another vacuum pump...