Search:

Type: Posts; User: maustin

Page 1 of 6 1 2 3 4

Search: Search took 0.00 seconds.

  1. Thread: EPA Reward

    by maustin
    Replies
    13
    Views
    4,485

    Poll: Do you work for the county and their operation is...

    Do you work for the county and their operation is being checked or is the county conducting the investigation? Either way as long as you have your log book you should be good to go.
  2. Replies
    2
    Views
    1,279

    Thanks, looks like a good source for replacements...

    Thanks, looks like a good source for replacements too.
  3. Thread: EPA Reward

    by maustin
    Replies
    13
    Views
    4,485

    Poll: I spoke with an EPA compliance agent last year....

    I spoke with an EPA compliance agent last year. He told me that the EPA is "disinterested" in pursuing reports of venting. The effort they do put forth on the subject is directed toward appliance...
  4. Replies
    3
    Views
    896

    75 if its 3/4" studs.

    75 if its 3/4" studs.
  5. Replies
    21
    Views
    2,994

    How about the Dolphin? Is it working?

    How about the Dolphin? Is it working?
  6. Replies
    10
    Views
    1,483

    Check with Mitchell Instruments, they have a line...

    Check with Mitchell Instruments, they have a line of process loop calibrators.

    I picked up one of their low end units, $400, and it works great to provide either a 0-10V or 4-20 ma signal.

    You...
  7. Replies
    5
    Views
    592

    There is likely an alternating relay. If so then...

    There is likely an alternating relay. If so then the pressure switch with the higher setpoint will normally operate the alt relay and thus the starter for the lead compressor. If the lead compressor...
  8. Replies
    9
    Views
    3,798

    Try searching the VA website. They have a...

    Try searching the VA website. They have a comprehensive set of specs available online.
  9. Replies
    2
    Views
    1,279

    Danfoss VLT Micro drive

    Does anyone have any experience setting one of these units up? Got one to use on a cooling tower fan. The programming manual is pretty vague and not very intuitive.

    Any constructive input is...
  10. Replies
    12
    Views
    1,977

    My new JB eliminator, 5 cfm I believe, with a...

    My new JB eliminator, 5 cfm I believe, with a 1/2" hose just pulled a 600 ton centrifugal from atmospheric to 750 microns in 24 hours. I changed the oil once before I went home for the night.
    ...
  11. Run the pump when the forecast calls for...

    Run the pump when the forecast calls for temperatures that you expect to cause freezing in the attic.

    We run about 30% +/- glycol solution in our chilled water loops, if I recall that is good down...
  12. Replies
    3
    Views
    856

    Try http://www.cmpcorp.com

    Try http://www.cmpcorp.com
  13. Read the manuals that are available on this site,...

    Read the manuals that are available on this site, there are tons of them! I may be considered a junkie, but I'll read a manual for the fun of it.
  14. Replies
    11
    Views
    2,131

    I've seen that or a very similar message on the...

    I've seen that or a very similar message on the one line marquee type display when the machine had air in it. Check your condenser approach and purge rate. Maybe York56 will chime in here.
  15. Replies
    3
    Views
    2,668

    Air Handler Services Inc. 16933 S. Hattan Rd....

    Air Handler Services Inc.
    16933 S. Hattan Rd.
    Oregon City, OR 97045
    503-631-7560

    Don't remember the fellas name there, but he quoted some shafts and wheels for us a few years ago on a early...
  16. Replies
    11
    Views
    2,131

    Are you getting a message to the effect of "evap...

    Are you getting a message to the effect of "evap pressure tranducer out of range" ?
  17. Replies
    9
    Views
    801

    overcurrent

    overcurrent
  18. Replies
    5
    Views
    1,368

    Is it an XWC 530? Is it showing harvest fail?

    Is it an XWC 530?
    Is it showing harvest fail?
  19. Replies
    18
    Views
    1,270

    When I owned my shop my philosophy was "I can...

    When I owned my shop my philosophy was "I can make nothing doing nothing"
    :couch:
  20. Search this section, there are a ton of factory...

    Search this section, there are a ton of factory manuals that members have provided. Download them and start reading.
  21. Replies
    18
    Views
    2,856

    We just put one in.

    We just put one in.
  22. Replies
    18
    Views
    2,856

    ICP CAE090GHC, is the 208 volt, 3 phase model....

    ICP CAE090GHC, is the 208 volt, 3 phase model. Dual copeland scrolls, GE fan motor. I've havent had any trouble with them. $2500 out the door at United Refrigeration. Its a single circuit though.
  23. Replies
    8
    Views
    1,287

    If the breaker serves just the 359 amp compressor...

    If the breaker serves just the 359 amp compressor NEC table 430.52 says that the breaker can be sized at 250% RLA. If the breaker serves the machine with more than 1 359 amp compressor, it would be...
  24. Replies
    11
    Views
    814

    These are the times that make me glad that I gave...

    These are the times that make me glad that I gave up being a field tech years ago and hired on with a state agency as an in house hvac tech at a large institution. I've read a lot bashing of the "in...
  25. I just changed out an old 30GB055 and an ALR060...

    I just changed out an old 30GB055 and an ALR060 with a new YCAL134. I don't know where you are located but I used vinyl jacketed styro foam insulation and applied embossed aluminum skin that came...
Results 1 to 25 of 130
Page 1 of 6 1 2 3 4
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event