Search:

Type: Posts; User: williediesel

Search: Search took 0.00 seconds.

  1. Replies
    6
    Views
    598

    Subcooling was 11 degrees and suction pressure...

    Subcooling was 11 degrees and suction pressure was 165 and discharge pressure was 265
  2. Replies
    6
    Views
    598

    The house is a track home 5 years old I checked...

    The house is a track home 5 years old I checked the welds and found no oil staining so I don't think they were leaks
  3. Replies
    15
    Views
    973

    Yes I'd like to apply of pro soon

    Yes I'd like to apply of pro soon
  4. Replies
    15
    Views
    973

    O and I did mean thermistor

    O and I did mean thermistor
  5. Replies
    15
    Views
    973

    Sorry I just didn't understand the question at...

    Sorry I just didn't understand the question at first I'll have to run to my work van and look at my notes
  6. Replies
    15
    Views
    973

    I'm a service tech with Sheetmetal worker local...

    I'm a service tech with Sheetmetal worker local 104 san francisco bay area I could put my thermocouple in the evaporator but would that give me the evaporator temperature or are you asking actual...
  7. Replies
    15
    Views
    973

    How do you find the evaporating temperature ?

    How do you find the evaporating temperature ?
  8. Replies
    141
    Views
    16,550

    Local 104 Sheetmetal workers sf bay area

    Local 104 Sheetmetal workers sf bay area
  9. Replies
    15
    Views
    973

    That's why the evaporator is freezing up not...

    That's why the evaporator is freezing up not enough cfm going past the coil
  10. Replies
    15
    Views
    973

    Subcooling was 11 degrees and I checked that I...

    Subcooling was 11 degrees and I checked that I didn't check static pressure but it sounds like the duct work is undersized huh what sucks is my company installed this system before my time so now I...
  11. Replies
    15
    Views
    973

    carrier infinity problem

    I had a service call were a 5 ton carrier 2 stage infinity system was giving me a possible evaporator frozen code at the thermostat? i checked the charge it was good checked for leaks no leaks? txv...
  12. Replies
    6
    Views
    598

    txv problems

    so do txvs go bad after sometime. i had a service call on a 410a carrier system. suction pressure was low 60 psig. discharge pressure was 235 psig. I let the home owner know her txv was bad and...
  13. Thread: Sam3???

    by williediesel
    Replies
    4
    Views
    621

    No problem I called your support # and spoke to...

    No problem I called your support # and spoke to someone they said I could send my sman3 back for a new one. It works great I'm just worried about the crack on the plastic right above the suction side...
  14. Thread: Sam3???

    by williediesel
    Replies
    4
    Views
    621

    Sam3???

    So I just got this new manifold it works great but...the clamp broke the first week I had it then this last Friday I seen a crack in the plastic right above the suction side what gives....?
  15. Replies
    9
    Views
    517

    ok thanks! you know sometimes its nice to have a...

    ok thanks! you know sometimes its nice to have a outside option on calls that we may get stumped on. tech support is hard to get a hold of .............sucks!
  16. Replies
    9
    Views
    517

    Right on bro I'm in the gettos of Hayward but my...

    Right on bro I'm in the gettos of Hayward but my company is out of Pittsburg we work all over the bay we do maintence and tract homes retro fits alway nice to meet someone from the bay !
  17. Replies
    9
    Views
    517

    Ok I like this forum so I'll post so I could get...

    Ok I like this forum so I'll post so I could get some advice on service calls that 15 you say to get membership
  18. Replies
    9
    Views
    517

    I'm a tech from the San Francisco bayarea I was...

    I'm a tech from the San Francisco bayarea I was just looking for some tip on what to Look for next service call I get from this homeowner
  19. Replies
    9
    Views
    517

    zone system

    I was woundering if the great minds on these threads could help me out I have a rheem 80% furnace with a honeywell zone board and damper. when zone 1 calls for heat the system goes into prepurg then...
Results 1 to 19 of 19
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event