Search:

Type: Posts; User: Nuclrchiller

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    14
    Views
    308

    Desired cooling tower setpoint is a compromise:...

    Desired cooling tower setpoint is a compromise: between as low as possible (for energy efficiency), but not so low as to cause problems with the chiller. Consult with the chiller manufacturer for the...
  2. A USB port for charging a phone. Another great...

    A USB port for charging a phone. Another great idea!

    I'm really liking the idea of a cordless heated jacket, adapted to a leather motorcycle jacket. As opposed to the current plug-in jackets. To...
  3. Replies
    14
    Views
    308

    This is the type situation where regularly...

    This is the type situation where regularly logging the equipment could show how the savings in lowering the sensible load compares to increasing the latent load.
    I would log the chillers just prior...
  4. Replies
    17
    Views
    406

    Or the saying that "you should never meet your...

    Or the saying that "you should never meet your heroes". :grin2:
  5. Saw where they come in non-hoodie styles, too....

    Saw where they come in non-hoodie styles, too.
    The video for one said "six hours of continuous use".
    Looks like a great idea.
  6. Replies
    10
    Views
    403

    My previous place of employment had a selection...

    My previous place of employment had a selection of 3/4 inch hoses with assorted fittings that was kept stored in a large plastic garbage can. It went with the large, wheeled recovery machine and the...
  7. Replies
    8
    Views
    510

    I suspect you guys don't expect to be doing that...

    I suspect you guys don't expect to be doing that work there. That work will most likely also be bid, using the least amount of manpower. Moving the additional rigging to the site will add to it....
  8. Replies
    8
    Views
    510

    Concerning that piping, how was it verified that...

    Concerning that piping, how was it verified that no construction debris was washed up against the tube sheet?
    I suspect that it wasn't checked.

    I don't mean to bust anybody's hump over this, but...
  9. Replies
    8
    Views
    510

    It does look nice, but I feel for the guy who has...

    It does look nice, but I feel for the guy who has to plug or replace a tube. Long, awkwardly shaped sections of pipe to remove and reinstall. All to save the expense of some pipe flanges.
    Chiller...
  10. Replies
    60
    Views
    1,654

    Inside temp is 70, and unit not cooling?

    Inside temp is 70, and unit not cooling?
  11. Replies
    19
    Views
    662

    Thanks for explaining that. :cheers:

    Thanks for explaining that. :cheers:
  12. Thread: spoons

    by Nuclrchiller
    Replies
    4
    Views
    450

    Hey Kefah, I hope you realize that story is a...

    Hey Kefah, I hope you realize that story is a joke. Not a true story. At least I hope it is not true.

    After 2sac's bikini pictures I was hesitant about reading this...
  13. Replies
    4
    Views
    314

    When I was young and just starting out on my own,...

    When I was young and just starting out on my own, I lived in a mobile home. I had this idea of using a pump spray air freshener to keep my house smelling fresh. Hey, for a single guy, I figured that...
  14. Replies
    19
    Views
    662

    This a presumption on my part: The inverter will...

    This a presumption on my part: The inverter will keep the motor from pulling an actual locked rotor amps, because it ramps it up to speed. In other words, the motor will not see full applied voltage...
  15. Thread: Why?

    by Nuclrchiller
    Replies
    30
    Views
    1,085

    I also think, that even in areas where licensing...

    I also think, that even in areas where licensing is weak, good HVAC techs have a well-rounded skill set. Most seem to be strongest in the mechanical aspect. So they, or the company they work for,...
  16. Replies
    19
    Views
    1,865

    C, did you have a Monza?

    C, did you have a Monza?
  17. Replies
    71
    Views
    20,038

    Have a link to an unbiased third party?

    Have a link to an unbiased third party?
  18. I use an IR for quick checks, too. I've noticed...

    I use an IR for quick checks, too. I've noticed that when I check one of my building's water heater, supplying the kitchen, the temp at the recirc pump is 20-30 degrees lower when measured on the...
  19. Replies
    11
    Views
    1,772

    Thanks.

    Thanks.
  20. Replies
    11
    Views
    1,772

    I have two questions: 1. Is that handle all...

    I have two questions:

    1. Is that handle all the way up, in the "On" position? Looks like it.

    2. Does each knife make contact on only one side? Again, looks like it. I have never seen a...
  21. That you know of....

    That you know of....
  22. I believe an IR "gun" thermometer is the most...

    I believe an IR "gun" thermometer is the most unreliable thermometer there is. It is also the most easily manipulated. Those are the reasons that it is so commonly used in YouTube videos and...
  23. I'm glad things there are moving in a direction...

    I'm glad things there are moving in a direction you like.

    And I'm glad to see you posting in other threads here, threads that are work related. I hope that means things are getting at least a...
  24. Replies
    41
    Views
    2,789

    My favorite summer time snack is white (sometimes...

    My favorite summer time snack is white (sometimes called green) seedless grapes. I keep them refrigerated at home and on ice when on the go. Like melon, they help me to stay hydrated. And they...
  25. Replies
    22
    Views
    3,574

    I especially like the statement in the patent...

    I especially like the statement in the patent application, "Most air conditioning components were designed to use the larger Freon 113 until it was banned...". Really? All of the R113 chillers I've...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event