Thanks. How did you figure out it was a carbonator? I asked the business owner if I could buy it from him and he agreed.
hopefully at some point I will have it here at the shop to play with.
Type: Posts; User: johndief
Thanks. How did you figure out it was a carbonator? I asked the business owner if I could buy it from him and he agreed.
hopefully at some point I will have it here at the shop to play with.
More Pictures851981851983851985851987
Next time I am there I will get more pictures.
It is not running or hooked up to anything. It is in a compressor room of and old general store in a small town. Everything in this compressor room has been abandoned. it has bastian blessing on the...
836747 I think this is an old compressor of some type can anyone confirm.
A bullhead tee is the correct way to do it with as close to equal distance to the coil inlet as you can get for proper liquid feeding.
R449A
835960835961835962835963
I will get a pair of those and try them. Thanks to everyone for the for the help.
That is what I have been using. I doesn't seem pinch off tight enough. Maybe something wrong with mine.
I think they are made to make a crimp that can be opened back up. that old style that...
I am looking for a press on cap to seal the process tubes on R290 units similar to the ones that come on the units from the factory. The manufactures do not want access fittings left on the system...
Check the wires behind the evap fans sometimes the rub on the fan mounts and will short out
Another company was working on this all day the day before I got there could not figure it out. seemed pretty obvious to me.802396802397
High Sierra unit not defrosting. Suction pressure running in vacuum during defrost. Removed biflow txv and solenoid and
replaced with standard txv and solenoid.
The panel you see there was bent in and the product fell in there through the seam between the bottom panel that I removed and the panel above it.
i did not notice anything in the fitting I will check it again tomorrow
The blades that were to pierce the brass plug broke they only partially pierced the plug causing a restriction.
4' section of 12" case warm. bad fan motor, No. Bad TXV, no. Iced up, No. dirty coil, No. It was bacon.768031
Brand new W-I freezer unit on roof short cycling,768021 suction pressure at coil 45lbs. Cant see how the installer walked away without at least trying finding the issue.
Just in case you want to wheel this gem around to show your friends.740421
Is it short cycling on the compressor overload or on the thermostat.
Is it short cycling on the compressor overload or on the thermostat.
And you wont have to waste all that money on the factory parts they are too expensive. I betting that is how the
conversation went.691361
Heat run in bathroom in restaurant. The wood is the ceiling.
This is an old school meat market that still cuts meat off hanging meat. Family owned for years and there stuff is high quality. I dont know why the pictures turned they were in the correct position...
New condensing unit, new low velocity electric defrost coils and a defrost panel.684021684031684041
New chain restaurant. I am guessing the print for the walk-in showed the evaporator in the center of the walk-in like they always do
cause the guy who does the drawing has no idea where it should...
looks to me like your cap tube is partially plugged.
There is no way adjustable nozzles should ship standard. Can you imagine the mess there would be when hacks started adjusting nozzles. They should be an option for those that could set them up. Not...
I think that was a factory condensing unit. I did not spend a whole lot of time on it. He wanted me to kind of fix it for not much money. He had it sold and it had to work for him to be able to sell...
Compressor stopped pumping.
Someone brought this trailer unit to my shop. He told me it always worked good but now it was not. Compressor was over amping and shutting down on overload.
I told him to take it back to the Amish...
You could be right about it always being a dairy cooler, it does not look like there is any heat in the pan so could not be low temp. I was looking for a
leak on this system and when I opened up the...
How well do you think it would defrost? I bet it would be more even than your standard electric defrost coil almost like hot gas defrost. I would think it would defrost better with refrigerant in the...
A couple more picks.
The other end looks the same if memory serves me right. I was there a couple mounths ago. It is in a homemade cooler in what used to be a milk plant. It is still used for milk storgage, but what it...
Never seen them done this way. Anyone now how well they worked. This coil is only used for medium temp so I have not seen them operate.
The part of the coil feed first would ice up. Ice was 3" thick when I got there.
This coil has a split evaporator with the fan in the center. I replaced the TXV with a sweat valve, new dryer and sight glass and cleaned the coil.
3 door Perlick back bar unit. Unit must be 40 years old and I think has been this way since day one. 619041619051
567461My service truck, pickup with cap
The inside I think is wood. Top door was for loading ice. Owner said he was offered 25k for it but would not take it.
Ran across this walk-in in a bar when I was away.
Anyone have experience with Hussmann rear feed dairy doors. Mo#D5-12LUR.
Only looked at them quick but I cant see how to get the doors out repair the rollers.
Didn't call Hussmann yet came here...
Yep, hitting iced up evap coil.
Yes, I had to work on a 2 door case there.
I think I was working at the same place today. You could melt those coils down and have enough raw materials for 5 modern coils.
He wanted to replace all the equipment he had with new stuff.
Small meat packing plant in rural area literally in a town with 10 houses. Open drive units serves the cutting room. Copeland semi does the freezer. I did not know if I should put this is WOS or WOP....
You are correct.