Search:

Type: Posts; User: Greend88

Page 1 of 15 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    48
    Views
    928

    Cast Iron Fittings Can Be Found under IFGC:...

    Cast Iron Fittings Can Be Found under IFGC: 403.10.4 - 5
    http://publicecodes.cyberregs.com/icod/ifgc/2000/icod_ifgc_2000_4_par042.htm

    Cast Iron Pipe is Prohibited.
  2. Replies
    48
    Views
    928

    The IFGC 2006 has the exact same thing under...

    The IFGC 2006 has the exact same thing under section 403.9
    http://publicecodes.cyberregs.com/icod/ifgc/2000/icod_ifgc_2000_4_par034.htm?bu2=undefined
  3. Replies
    48
    Views
    928

    http://www.detroitnippleworks.com/merchant-couplin...

    http://www.detroitnippleworks.com/merchant-couplings/

    Straight threads make them easy to loosen up with any type of vibration.

    The UPC 2003 Says For Fuel Gas Piping: "1209.5.7 Metalic Pipe...
  4. Replies
    15
    Views
    386

    Your Missing Something.... You make a loop...

    Your Missing Something.... You make a loop between the two heaters.
  5. Replies
    15
    Views
    386

    You can do it either Parallel or Series, both...

    You can do it either Parallel or Series, both have there pros and con's google it. And make sure to check with your Local Inspector as said above.
  6. Replies
    6
    Views
    233

    Yes you do need to be certified....

    Yes you do need to be certified. http://codes.ohio.gov/oac/1301:3-7-02

    And if you get caught here's the fine: http://codes.ohio.gov/orc/3703.21
  7. Replies
    10
    Views
    462

    Havn't Tried this but couldn't you take a dual...

    Havn't Tried this but couldn't you take a dual port manometer and cap off one port with a piece of plastic tubing with a valve. You can get them at aquarium shops. Place this tube on the manometer...
  8. Replies
    16
    Views
    625

    Oil Separator, and get it back to the compressor....

    Oil Separator, and get it back to the compressor. As long as it's not running 24/7 it won't hurt it. Seen Fridge Compressors last forever as airbrush compressors.
  9. What did you set the Ice Thickness Probe? Should...

    What did you set the Ice Thickness Probe? Should be 9/32"

    http://www.manitowocice.com/asset/?id=pnvoq

    See Page 100 for setting Probe.

    "During the first 6 minutes of the freeze cycle the ice...
  10. Replies
    14
    Views
    559

    You could rewind a couple used 1200 watt...

    You could rewind a couple used 1200 watt microwave transformers (MOT's). I've seen it done to make cheap arc welders before. Just make sure there in phase and do the math to figure your winding size...
  11. Replies
    30
    Views
    1,566

    HS36 Gets my Vote Have had mine for over 2 years...

    HS36 Gets my Vote Have had mine for over 2 years and no problems at all.
  12. Replies
    19
    Views
    1,515

    Service Wrench and Extension Like everyone else...

    Service Wrench and Extension Like everyone else said ^
  13. Thread: Pulley puller

    by Greend88
    Replies
    33
    Views
    1,172

    Harbor Freight has a couple Hydraulic Pullers for...

    Harbor Freight has a couple Hydraulic Pullers for less than a $100

    http://www.harborfreight.com/catalogsearch/result?q=Hydraulic+Gear+Puller
  14. Replies
    45
    Views
    1,780

    Dont worry bout the teflon tape. I use it on all...

    Dont worry bout the teflon tape. I use it on all gas pipe never had a problem. As long as its put on correctly itll never get in the pipe.
  15. Replies
    22
    Views
    1,217

    The reason for no staybrite8 in commercial...

    The reason for no staybrite8 in commercial buildings on pipe systems would be to keep the joints from melting in a fire and introducing a ton of refrigerant.
  16. Replies
    45
    Views
    1,780

    All Appliances should be isolated, and the meter...

    All Appliances should be isolated, and the meter should be isolated before any pressure tests are done.
  17. Thread: Turbo torch

    by Greend88
    Replies
    41
    Views
    2,809

    I've brazed 3" Copper easily with a TurboTorch...

    I've brazed 3" Copper easily with a TurboTorch and there largest tip. It all depends on the tip you use.
  18. Replies
    47
    Views
    3,816

    Looks Great

    Looks Great
  19. Most good digitals are 0.5% accurate... So a 0.5%...

    Most good digitals are 0.5% accurate... So a 0.5% difference between 1% analogs and digitals.
  20. Replies
    12
    Views
    759

    A Good EMPulse will energize the locks and open...

    A Good EMPulse will energize the locks and open them.

    Also Car's with Tire Sensors,Blue Tooth, OnStar. The CANBus can be wirelessly hacked to Unlock and Disarm the Factory Alarm.
  21. Replies
    2
    Views
    255

    Is there any booster pumps tied in right after...

    Is there any booster pumps tied in right after the backflow? Also any large call for water and sudden stop will cause them to pulsate. Anytime the pressure after the backflow is greater than the...
  22. Replies
    9
    Views
    553

    Have you guys read the ingredients on those flush...

    Have you guys read the ingredients on those flush kits? Mostly Acetone.... At least the ones sold around here are.
  23. Replies
    45
    Views
    3,636

    When your doing liquid remember to meter it with...

    When your doing liquid remember to meter it with your gauges. Start closed then work to open making sure your not overpowering the unit. I've seen way to many techs slam them with TOO much liquid and...
  24. Replies
    21
    Views
    978

    I believe this one was leaking internally....

    I believe this one was leaking internally. Swapped it out the next day and no more problems.

    446671446681446691446701446711446721
  25. Replies
    5
    Views
    448

    http://www.digikey.com/schemeit

    http://www.digikey.com/schemeit
Results 1 to 25 of 359
Page 1 of 15 1 2 3 4
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event