Type: Posts; User: shifrbv
Search took 0.01 seconds.
Is ductwork in the attic? Is it old black R4.2 vs new silver (black) R6? Is it properly sized?
I have tried same setup as you did few years ago. Running fan all the time in the winter did not work for me either. Bill went up, and just about it. I installed manual dampers at the trunc takeoffs...
I was in the same situation once, system was installed by expert hack.
Remedy was not as bad as I thought.
Opened drywall in the next section of 2x6 run another flex from crawl trunc...
That was wrong, after all, he did absolutely nothing.
And Browny was such a qualified candidate.
It is really interesting how republican liars using term as "natural occurrence" instead of...
Same bologna arguments
I would ask seller for 3k off price of the house.
Now that seller is aware of the problem he/she would have to list it on the sale form.
Might be normal,
Mine (VP8320) takes few min to take effect.
Like if I change tstat fan from ON to AUTO, or adjust
settings from ON to OFF system runs for few more minutes.
Anyone hear of residential install of
Honeywell economizer ( such as 7460 ).
I know it is been used for light com buildings.
Was thinking might be cool for my house.
Funny, my wife always posts under guy nicks....
( not to this forum tho )
>What is the proper direction for facing the grills.
>Should the vanes point up or down.
Up for estetics, really I bet it does not make any difference ( well may be 0.00001%).
I could see how...
I used writeSoft myself,
if you didn't enter correct air infiltration, people, appliances etc - results may vary.
My read on your situation:
Contractor 1: if thought was 3T does not work...
Can I contact you outside of this forum about this change? I understand there is $200 rebate from Cinergy for Installing 14SEER HP. Don't know if this worth going for.
Long day, think before you post.... ( Duh! )
I meant to ask about ceiling boot sizes for 6" supplies.
a) 2 1/4 x 12
b) 3 1/4 x 10
c) 4 x 10
d) 4 x 12
Ceiling registers in the basement
What would be the good size to go with....
Basement zone will have 5 x 6" supplies.
First Nighthawks don't last five years, they warranted for five years.
Second they use solid state CO sensors. Those never loose calibration nor contain any chemicals that needed refill.
It is NOT a good idea to "ohm" boards, unless manufactures told you to do it.
You are applying voltage to the non powered boards. Current from your ohm meter can, may and probably will burn p-n...
PG9MAB newer line, existence PG9MAA has something to do with been certified in California to meet Env standards...
036 - 3T
042 - 3.5T
048 - 4T
060 = Input BTUH 60,000
>Sounds steep ...
Sometimes one can spend hours getting old $@%$^& wheel off.
I am non pro, and zoned only my own house.
Just like in your case two story entrance.
I used Elite Rhvac, but I am sure you can use hvac-calc.
Create two projects, in the first project...
You can buy one from Lowes ( in some states ) no questions asked.
They even have chart sq ft house => ton / BTU of equipment. :)
I pissed with my installer, since they equipment that has been...
I also had house built ~3400sq ft 80% Single Stage bryant 311AAV048-110 CK5P 343G state: IN.
Closing dampers did absolutly nothing to my bill....
Try it if you have lot's of free time.
I have return duct 20x25 with 1" opening at the top to insert/remove standard filter.
Was thinking about upgrading to 5" media filter.
What is that wire with a lots of electrical tape that wrapped around the gas line?
Hope electrical tape is not a service disconnect....
Oh no, they might remove that blinking LED :)