Search:

Type: Posts; User: control$

Page 1 of 13 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    21
    Views
    3,069

    Have you every used it? Every copy sold was a...

    Have you every used it? Every copy sold was a beta site. Bugs all over the place, and crashed to no end. Tech support was almost 0 when they where in buisness.
    I wish you luck, it was way ahead of...
  2. Replies
    279
    Views
    21,747

    Still got to go with ALC after all these years....

    Still got to go with ALC after all these years. Still kicks the pants off all the other crap I install and service.
  3. Replies
    4
    Views
    598

    Hope this helps. ...

    Hope this helps.

    http://www.automatedlogic.com/eikon-for-educators/%20/
  4. Replies
    3
    Views
    319

    All I can say is it painful. I've done a lot of...

    All I can say is it painful. I've done a lot of these, and it seems everytime it's like relearning the wheel. Every system seems to change. Sometimes we wire the network to the blower, other times to...
  5. Replies
    9
    Views
    295

    Shoot me an e-mail.

    Shoot me an e-mail.
  6. Replies
    9
    Views
    295

    I believe I have most of the RZ manuals and...

    I believe I have most of the RZ manuals and related info. PM if interested
  7. Replies
    19
    Views
    646

    It's a company thing. Did an Invensys job once...

    It's a company thing. Did an Invensys job once with at least 50 vav with the same neuron id. Blame the company and not the protocal.
  8. ALC defaults to 16. Your in charge at 15 or...

    ALC defaults to 16. Your in charge at 15 or below. You have 3 states. "on" "off" "null" make sure your sending a "null" command to release the overide to ALC

    482141
  9. Guess so.

    Guess so.
  10. They really should use Arcnet, no reason not to...

    They really should use Arcnet, no reason not to It's ok by ASHRAE and runs circles around MS/TP. But that being said i've never found it that hard to find ANY control from any vender. Let's be honest...
  11. I know your going for an angle here. But some of...

    I know your going for an angle here. But some of my largest networks are straight MS/TP with every type of control on the same wire.
  12. Your dealing with OEM and not ALC. OEM venders...

    Your dealing with OEM and not ALC. OEM venders tend not to understand the controls end all that well.
  13. Guess it's just too difficult to enable Network...

    Guess it's just too difficult to enable Network Visible. ALC provides ALL the tool needed for any third party. Wish all systems where as nice.
  14. "Having Webctrl's programming tool won't do you...

    "Having Webctrl's programming tool won't do you any good at this point unless you have the site specific system files" - ??!?! How would WebCTRL running exec B even run without the .equipment file?
  15. Distec- Damm do I miss that NW8000. Still better...

    Distec- Damm do I miss that NW8000. Still better then what's out today.
  16. Replies
    6
    Views
    462

    Get a few bids to get a feel of the cost. But if...

    Get a few bids to get a feel of the cost. But if your Alerton rep has been good then you'll save a lot of $$ if you stick with them.
  17. Replies
    45
    Views
    2,224

    Well I work with both. Most tech's I know like...

    Well I work with both. Most tech's I know like bacnet.
  18. Replies
    12
    Views
    603

    "I once worked in an enterprise where...

    "I once worked in an enterprise where electricians were paid more than control technicians and some engineers!"

    Exactly where do you live where this isn't this the case?!!
  19. Replies
    45
    Views
    2,224

    Learn whatever your selling. Then come back here...

    Learn whatever your selling. Then come back here in 2 months and swear it's the best.
  20. Replies
    9
    Views
    364

    You would really have to question the logic of...

    You would really have to question the logic of doing this to 1994 technology. The 9600 baud legacy com will be slow and from the sound of 850 points you must have many LGE's on site. Is your plan to...
  21. Replies
    9
    Views
    599

    Here's a point list of a Carrier 19xr that I'm...

    Here's a point list of a Carrier 19xr that I'm working on. The UPC open works, but I get more useable point's from the '95 vintage trane.

    474631
  22. Replies
    21
    Views
    1,466

    Hey I still "maintain" the old Barber-Colman RED...

    Hey I still "maintain" the old Barber-Colman RED / Black controls ..old 5608A still glowing.
  23. Thread: Trucks

    by control$
    Replies
    23
    Views
    1,090

    I worked with a job Union Electrian years ago...

    I worked with a job Union Electrian years ago that for years was looking at Harleys. One day he rode up on a Honda. I asked why? He said it was cheaper, rode better, and far better quality.

    True...
  24. Thread: Trucks

    by control$
    Replies
    23
    Views
    1,090

    The last Chevy Astro I had back in '04 had over...

    The last Chevy Astro I had back in '04 had over 200000 miles. Had 1 ton van's and finally I got 1/2 ton in '09. Osiyo your right. As a service tech I don't need more room then a small van. And the...
  25. Replies
    16
    Views
    785

    1MHz or greater bandwidth and a sampling rate of...

    1MHz or greater bandwidth and a sampling rate of at least 5 megasamples per second.
Results 1 to 25 of 304
Page 1 of 13 1 2 3 4
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event