Search:

Type: Posts; User: mallron

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. I have several VFD's out there that are being...

    I have several VFD's out there that are being controlled via 2-wire comm and haven't had any problems with them at all, but there's still that part of me that prefers hard wired control.
  2. Replies
    3
    Views
    346

    Put a temp sensor in the return in you don't have...

    Put a temp sensor in the return in you don't have one in the space and jack you daytime warm-up and morning warm up settings to 80 or so. I assume you have heat in the RTU?

    Make triple sure that...
  3. Replies
    8
    Views
    371

    And yes they are Danfoss drives with Tranes name...

    And yes they are Danfoss drives with Tranes name on them.
  4. Replies
    8
    Views
    371

    I have done a few of these but I remember...

    I have done a few of these but I remember installing BACnet cards because they originally shipped with LON cards and we had to get BACnet cards overnighted. Set-up was simple however and they worked...
  5. Replies
    2
    Views
    280

    IP wouldn't be tough if you have Summit. You...

    IP wouldn't be tough if you have Summit. You would definitely need a hi cap card and reference all the info you would want to expose as BI, BO, AI's and AO's. If you have Summit
    it would be a ton...
  6. did you guys ever get this one figured out? I'm...

    did you guys ever get this one figured out? I'm having a similar issue except the Corel controller doesn't seem to take the start/stop command at all, but I get temps etc at my front end.
  7. Replies
    3
    Views
    362

    The BMTX BCU is capable of communicating to the...

    The BMTX BCU is capable of communicating to the UCP 1 and/or the UCP 695 panels. The BCU must be 2007 or later and have
    the latest firmware. I've wired up quite a few of them.
  8. Thread: Trane CPL

    by mallron
    Replies
    2
    Views
    346

    connect to the BCU with you Tracer Summit...

    connect to the BCU with you Tracer Summit software and choose "set-up" then scroll down to "custom programming". a window will pop up, close it and choose "program" at the top of the screen, then...
  9. Replies
    3
    Views
    386

    I'm still trying to figure this one out. I think...

    I'm still trying to figure this one out. I think it may be a problem with my PC specifically because I installed TU on a desktop that had basically the same config as my labtop and TU starts on the...
  10. Replies
    3
    Views
    386

    Tracer TU...again

    Anyone had issues with TU starting since the latest Java updates?

    I'm running Windows 7 and the only changes that have been made to my laptop since the last time I used TU
    were the Java updates...
  11. Replies
    4
    Views
    658

    You could have Trane replace the Tracer 100i...

    You could have Trane replace the Tracer 100i panel with a BCU relatively easily and would maybe cost 15k including a workstation and graphics. Having everything replaced with new controls would cost...
  12. Replies
    4
    Views
    385

    what board is in the unit? post a pic if you're...

    what board is in the unit? post a pic if you're not sure.
  13. I work at a zoo that's controlled by Tracer...

    I work at a zoo that's controlled by Tracer Summit, but it's actually a High School.
  14. I downloaded this, thanks Lunchbox

    I downloaded this, thanks Lunchbox
  15. I would try removing all override control except...

    I would try removing all override control except for heating/cooling setpoints and occupancy.
  16. Welcome aboard or to-the-board rather. I...

    Welcome aboard or to-the-board rather.

    I really don't have much to offer other than to say that I would think that it shouldn't matter where on the comm link the devices reside just as long as...
  17. Thread: Trane

    by mallron
    Replies
    2
    Views
    385

    They're usually included in Rover service packs.

    They're usually included in Rover service packs.
  18. Replies
    20
    Views
    1,750

    I don't see the point in operating the drives in...

    I don't see the point in operating the drives in bypass. If the towers are in an industrial/process application in which the cooling systems are always close to or at full load that still doesn't...
  19. Replies
    19
    Views
    3,976

    The part number is SFT1002 if I remember...

    The part number is SFT1002 if I remember correctly. Try Trane parts with that part number.
  20. Replies
    6
    Views
    780

    emergency shutdown is used for the fire alarm in...

    emergency shutdown is used for the fire alarm in most applications. you want remote shutdown and it's on the LVTB or low voltage terminal board. there's a metal factory jumper in place on the...
  21. Replies
    10
    Views
    1,916

    Thanks, Joey.

    Thanks, Joey.
  22. Replies
    10
    Views
    1,916

    I just got the software last week, I guess they...

    I just got the software last week, I guess they were getting rid of old stock.
  23. Replies
    10
    Views
    1,916

    This was it, I was attempting to connect with the...

    This was it, I was attempting to connect with the adapter connected to the BACnet bus because there were no stat drops. It actually says this in the manual but who reads those anymore? I can...
  24. Replies
    10
    Views
    1,916

    Yup, it won't start unless it's licensed, well,...

    Yup, it won't start unless it's licensed, well, it will launch but you won't get far.

    Update, I performed a "repair" of the TU installation and now I can direct connect but still can't connect via...
  25. Replies
    10
    Views
    1,916

    Ok, I downloaded the latest version of the BACnet...

    Ok, I downloaded the latest version of the BACnet service tool and now I can download measurement conversions into the UC400, but I still can't connect with TU at all. TU is version 8.2 BTW.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event