Search:

Type: Posts; User: hos

Page 1 of 2 1 2

Search: Search took 0.01 seconds.

  1. Thread: Loytec Modbus Help

    by hos
    Replies
    48
    Views
    3,750

    What exactly is this transmission delay used for....

    What exactly is this transmission delay used for. I have changed it from 0 to 100ms, to 200ms, 250ms, 500ms, 1000ms and have not found any difference.
    Also can you explain what the pollcycle time is...
  2. Thread: Loytec Modbus Help

    by hos
    Replies
    48
    Views
    3,750

    The tech from the Gen company had modscan and he...

    The tech from the Gen company had modscan and he could see the device on the same cable that is installed. He put the bias resistor on at the loytec end and set the bias resistor in the genset...
  3. Thread: Loytec Modbus Help

    by hos
    Replies
    48
    Views
    3,750

    Sorry did you not read the part about where i...

    Sorry did you not read the part about where i have 2 modbus meters reading fine, and if i unplug one then the readings from the unpluged meter come back as damaged.

    Either the generator is no...
  4. Thread: Loytec Modbus Help

    by hos
    Replies
    48
    Views
    3,750

    Frame damaged can mean the device does not...

    Frame damaged can mean the device does not respond, because i have some modbus meters that if i unplug the meter it comes back as frame damaged and there is no meter to respond, not just because the...
  5. Thread: Banned

    by hos
    Replies
    37
    Views
    3,441

    Hurry up and get Sysint back, he needs to answer...

    Hurry up and get Sysint back, he needs to answer my loytec post. LOL
  6. Thread: Loytec Modbus Help

    by hos
    Replies
    48
    Views
    3,750

    "You can check that box and then put in your...

    "You can check that box and then put in your multiplier and offset. No need to suffer. (screenshot)"

    Here's a good suggestion "What I find interesting is why the guy doesn't just email his config...
  7. Thread: Loytec Modbus Help

    by hos
    Replies
    48
    Views
    3,750

    Thanks Crab master for the assist in all this. ...

    Thanks Crab master for the assist in all this.

    If you see in the posts above the battery voltage say 538. The actual voltage on the read out display on the genset is reading 26.9 - 27V. The...
  8. Thread: Loytec Modbus Help

    by hos
    Replies
    48
    Views
    3,750

    How do you get the engine coolant being 40160? I...

    How do you get the engine coolant being 40160? I have put it in as decimal register 200. Is this wrong? I am using decimal in the loytec device.

    I am not sure if the system has a password set, i...
  9. Thread: Loytec Modbus Help

    by hos
    Replies
    48
    Views
    3,750

    I just upgraded the software to 4.2 and upgraded...

    I just upgraded the software to 4.2 and upgraded the firmware to V4.2.

    I have attached the config file. This is the best i've seen it so far, on first logging into the datapoints page all was...
  10. Thread: Loytec Modbus Help

    by hos
    Replies
    48
    Views
    3,750

    Polarity of modbus cable is correct, that was the...

    Polarity of modbus cable is correct, that was the first thing that was checked. All good.

    I had a tech come out from the generator company and he used moduscan to scan the device to see its...
  11. Thread: Loytec Modbus Help

    by hos
    Replies
    48
    Views
    3,750

    Loytec Modbus Help

    Hi All
    I hope you can help me with a problem i am having with a Loytec Linx200 Modbus-Bacnet converters.

    I am fairly new to modbus and don't know much about it as the controls we do are bacnet...
  12. Replies
    35
    Views
    4,741

    Thats some real nice work there. How long would...

    Thats some real nice work there. How long would it take you to make a picture like this one? I would think it would be around about 3-4hrs work, am i right?

    Very nice though. So you just import an...
  13. Replies
    9
    Views
    1,193

    Sent you the csv file Proto, i'm not sure that...

    Sent you the csv file Proto, i'm not sure that this can be changed. Maybe they have locked this feature so it can't be changed, which in my book is pretty useless as what happens when you have 2...
  14. Replies
    9
    Views
    1,193

    I have one of these meters that i'm testing, i...

    I have one of these meters that i'm testing, i can change the node ID but that does not in any way change the device instance. The device is bacnet IP only, it doesn't have MSTP.
  15. Replies
    9
    Views
    1,193

    Crompton Interga BACnet/IP meter

    Was wondering if anyone knows how to change the device instance on the Crompton Integra BACnet/IP meter. I have used ruinet to gain access to the csv file to make modifications. I have been able to...
  16. Replies
    38
    Views
    3,628

    Innotech are no longer a propreitry system they...

    Innotech are no longer a propreitry system they have now introduced BACnet into their hardware and their iComm server program. Not only are they open software(who give away their configeration...
  17. Replies
    35
    Views
    4,741

    We generally use autocad to pull the floor plans...

    We generally use autocad to pull the floor plans off, then make a jpg of them. Then we'll use photoshop to chage the colours etc
  18. Thread: Spyder Enhanced

    by hos
    Replies
    19
    Views
    1,446

    They have a good controller in their maxim111...

    They have a good controller in their maxim111 range with free software, what else do you want.
  19. Thread: People Counter

    by hos
    Replies
    1
    Views
    478

    People Counter

    Hey guys
    I have been asked to put 6 people counters on the doors of a shopping mall.
    What sort of information will they want to collect from these ie: total number of people and people per door.
    ...
  20. Replies
    0
    Views
    477

    LG Wiring Schematic

    Does anyone out there have a wiring diagram for a LG Ducted A/C
    Model LBF3660HL, its a 10.5KW reverse cycle unit.
    Im replacing the LG control with something better and need a wiring schematic.
  21. Replies
    0
    Views
    389

    LG Wiring Schematic

    Does anyone out there have a wiring diagram for a LG Ducted A/C
    Model LBF3660HL, its a 10.5KW reverse cycle unit.
    Im replacing the LG control with something better and need a wiring schematic.
    :)
  22. Replies
    32
    Views
    3,001

    As you have a load in the room even though it is...

    As you have a load in the room even though it is cold out side, install a hp control on the discharge pipe and set it up to a high setting like 2200kpa(r-22) and run a relay so that the condenser fan...
  23. Replies
    2
    Views
    551

    What happened to Turtle???????

    It's been a long time since i have seen a post from Turtle.
    Does anyone know whats happened to him?
    His posts were always go for a laugh!!
  24. Replies
    1
    Views
    1,727

    Sanyo Hermetic Compressor

    Hi all, just have a question on a Luke chiller(water cooled 2 comps) running on R-22 with liquid line solenoids each stage, the controls just got replaced with a ddc controller from original. The...
  25. Replies
    14
    Views
    1,638

    Is this a heat pump unit running under low...

    Is this a heat pump unit running under low ambient conditions?
  26. Thread: ugly women

    by hos
    Replies
    0
    Views
    958

    ugly women

    A loud unattractive, hardfaced woman walks into the supermarket with her 2 kids in tow screaming obsenities at them through the entrance. The door greeter says 'good morning and welcome, nice kids...
  27. Replies
    9
    Views
    2,210

    mate i'm not saying i'm defence less against...

    mate i'm not saying i'm defence less against anyone but the facts still remain you idiots are killing yourselves at a great rate. Don't think so.. here's a blurb from your oh so great NRA

    Firearms...
  28. Replies
    9
    Views
    2,210

    less gun crime than you bozo and thats a fact

    less gun crime than you bozo and thats a fact
  29. Replies
    9
    Views
    2,210

    right on mate us aussies have got to stick...

    right on mate us aussies have got to stick together
    you stupid yanks ought to take note
    pass me another VB
  30. Thread: duck

    by hos
    Replies
    0
    Views
    843

    duck

    A guy comes home from the pub with a duck under his arm and greets his wife.
    'This is the fat pig i've been f*cking' he says.
    'Thats not a pig, thats a duck' she says.
    He says 'I was talking to...
  31. Replies
    0
    Views
    375

    wiring diagram drawer

    Does anyone out there know where i can get some free software or shareware of a wiring diagram drawing program?
  32. Thread: Innotech DDC

    by hos
    Replies
    23
    Views
    3,653

    Are you still at innotech kaos or have you moved...

    Are you still at innotech kaos or have you moved on?
    Yes those vav controls are already out there.
  33. Thread: Auto matrix

    by hos
    Replies
    7
    Views
    1,042

    ok thanks guys, i don't know much about these...

    ok thanks guys, i don't know much about these controls so i haven't fiddled with them.
    The part # on this one i saw was SBC ASCE REV A 2005
  34. Thread: Auto matrix

    by hos
    Replies
    7
    Views
    1,042

    How do I go about Hyperterminaling into the...

    How do I go about Hyperterminaling into the system?
  35. Thread: Auto matrix

    by hos
    Replies
    7
    Views
    1,042

    ok i fixed the prob sort of by talking with a...

    ok i fixed the prob sort of by talking with a lady 700kms away and she switch (via modem i guess)all the relay and i found out that ralay k3 was stage 1 cooling which was stuffed, so i wired into...
  36. Thread: Auto matrix

    by hos
    Replies
    7
    Views
    1,042

    Auto matrix

    Came across an auto matrix controller the other day. Never seen them before, anyone know much about these controls, what are they like?
    Easy to use, reliable etc.....
  37. Thread: Innotech DDC

    by hos
    Replies
    23
    Views
    3,653

    what doing kaos, wiring or air con work?

    what doing kaos, wiring or air con work?
  38. Thread: Innotech DDC

    by hos
    Replies
    23
    Views
    3,653

    yeah it is cochlear, you been up there?

    yeah it is cochlear, you been up there?
  39. Thread: Innotech DDC

    by hos
    Replies
    23
    Views
    3,653

    http://img223.imageshack.us/img223/1274/image026pl...

    http://img223.imageshack.us/img223/1274/image026pl4.jpg
    Here's one of my job sites these 5 gen 2's are controlling 2 cleanrooms
  40. Thread: Innotech DDC

    by hos
    Replies
    23
    Views
    3,653

    Yes i have many sites with innotech controls,...

    Yes i have many sites with innotech controls, genesis 2s to maxims all networked. Just wondering if anyone in the states was using them as they originally come from brisbane australia, I'm from...
  41. Thread: Innotech DDC

    by hos
    Replies
    23
    Views
    3,653

    what do you mean by no gateways to open protocols?

    what do you mean by no gateways to open protocols?
  42. Replies
    3
    Views
    591

    Could be a way to get your foot in the door if...

    Could be a way to get your foot in the door if you don't know to much and learn as you go and then move on later to something thats more interesting to you.
  43. Thread: Innotech DDC

    by hos
    Replies
    23
    Views
    3,653

    have you found the controls accurate and reliable?

    have you found the controls accurate and reliable?
  44. Thread: Innotech DDC

    by hos
    Replies
    23
    Views
    3,653

    Anyone here using innotech digital controls and...

    Anyone here using innotech digital controls and if so how are you finding them?
  45. Thread: innotech

    by hos
    Replies
    0
    Views
    500

    Any one here using Innotech ddc controls on...

    Any one here using Innotech ddc controls on cleanrooms, high rise etc
  46. glide

    Had a carrier chiller with 4 6e comps running on 407c blow a pressure relief valve and dump half the refrigerant. Topped it up and wouldn't run. Kept tripping out on head pressure, had to reclaim and...
Results 1 to 46 of 63
Page 1 of 2 1 2
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event