Search:

Is it not the same thing if you were to perform the math?

GT

If you want to get more in depth, I would recommend applying for Pro status, this would allow you to basically converse tech to tech in the "locked" areas.

Do you know if any vibration readings...

We can't really answer any technical questions such as this in an open forum according to the rules.

However I must say that this is one of the best write ups I have ever seen on this site.

My...

Again, if it leaks at 250 PSI it will leak at 50 PSI..

Start low then high. Chances are you will find the leak quicker at the lower pressure. Seen it 1000 times.

GT

Not going to get into a pissing for distance contest with you, never said you can't use it, quite the contrary.

However, if not done properly, will chill the piping and cause a ton of condensation...

I think this discussion went way off track.

The OP mentions purge, not evacuation.

Purging with nitrogen is to "displace the oxygen during the brazing process", you have to realize that the...

Why are you testing with such high pressures?

Bubbles will not form around a crack.

If it leaks at 400 pounds, it will leak at 50 pounds..

Dyes suck.

Throw in some R22 as a trace gas and...

376251Picture (worth the proverbial 1000 words...)

And at the same time, you have to be careful what you say... You should not be wearing cut resistant glove "all of the time"... a Power tool constitutes almost all types of glove an absolute no no....

TTT

OK

I screwed up, bought a bunch of stuff for a job that fell through (company went belly up).

I paid well over $1200 each for these with shipping, had them for about a year (keep thinking a job...

Wha? :toetap:

Thinking that the OP is a troll.... :troll:

You can't just learn a few buzz words and think you can get information on something you know little/nothing about. Wrong forum...

Just so that you know my feelings on it...

How can I prevent going over on labor if I don't have the PM's proposal in my hand?

If you went over the quote on just materials to install what was...

Who cares....:whistle:

My opinion?

You did something incorrect, or missed something in the wiring.

How did you wire the motor? Did you wire it for three wire, or put the capacitor in harms way? I hate that.

What...

The run capacitor on a PSC literally provides the motor with the third phase.

Most aluminum framed capacitors are made in Mexico these days, I suspect that the quality of the raw materials and the...

Stupidity cannot be fixed and laziness would be where I institute my inconvenience tax. Bet that would only happen once or twice....


GT

Guess you didn't read the "hypothetical" part....

I oversimplified it to make a point to the extreme.

GT

I can't tell what was changed.....

Am I missing something?

Something that has not been mentioned much is the Chinese economy and what effects on the long term it will have to the world economy.

I get the feeling this has zero to do with nuclear...

Cover letter, really?

Maybe if he was applying for a service managers position, not a field grunt (no offense).

Single page lean and mean imho. You want the reader to be able to make the...

Don't take this the wrong way, but....


What are you applying for?

No where in your resume do you say what you want, only what you have done... For the record, nobody cares.

If the reader...

The calculations need to be performed to be able to properly answer that question, if a company wants to replace it with like for like just because that is what is in there, move on to another...

I may come off sounding a bit abrupt, for that I ask you to take no offense..

That being out of the way, what are you afraid of? replacing an out of date piece of equipment that is way past it's...

Well,

I really did not want to respond, but kept thinking about it, so here goes.

This has been happening to me for the last ten years.

I seem to get myself stuck on other tech's nightmares...