Search:

I have been witnessing a trend. Where in house BMS programmers are being replaced by
Lower paid remote programmers.The internet access to most of our sites permits this.
I was a little surprised...

That is the strange thing.Can log into the station.
Station/ Sevices/platform services.When we click on one of the platform services, nothing happens “Unable to find server”
If I recall you should...

Team viewer in last night
Prompted for platform login credentials, credentials no longer work.Am guessing that we have the correct primary IP if we are being prompted for credentials. Login...

Several JACES in schools had AX3.8 installed. Not too sure how they do that, Any how
We can open and view the JACE with Laptops that only run A. 3.8,.One JACE 8000
They can no longer access the...

Tried The medium level “ MED”
Username and password
Should I be using the LOW level
Username and password

Have one site, now having difficulties connecting
When USE Launchpad by Siemens to connect
the Site Name and Password Display ,as Always, except now
I receive "An I/O error has Occurred"
Tried ...

Electricians performed initial wiring
During commissioning, actuators were not working. Re-terminated leads from switches to Actuators.
Normally we can read the corresponding DC voltage at the...

Analog Outputs , on a Several Spyder controllers ,were connected
To closed switch contacts.All other Inputs and Outputs respond good.removed Wires from A.O. terminals,and commanded to 100% Am...

Previous tech changed the Baudrate on a JACE MSTP comm port _1
Everything was previously functioning OK
Bacnet devices Strykers and some Spyders are now going off line and a few minutes later,...

Have two JCI FEC controllers with Bacnet.
Both controllers Daisy chained to a Bacnet / IP router.
The IP part is connected to a Desktop running a photo shop program.
I an trying to link Bacnet...

No Supervisor PC.
All graphics pages on Two JACES.
Home graphics page for Niagara N4 is on JACE 192.168.1.140
On home page when clicking on “AHU Summary” button want to send
User to AHU page on...

On a Honeywell or even a JCI JACE BACnet Network,, Is the Contemporary Controls BASRTP-B Bacnet Router /IP to MS/TP , the only way to connect
to and Discover BACnet Devices. For other Third Party...

If I change JACE to 9600 will I see a difference in Spyder refresh Rate, The two spyders have many points, and viewed by a supervisor.
But the third party devices have just nine points each

Honeywell JACE. BACnet Ms/ TP network has
Two Spyders and three third party BACnet devices
JACE baudrate set for 38,400
Other three devices Default at 9600
To change their baudrate ,
12...

client uses a Safari web browser to view graphics.It appears all the Graphic pages are running on a JACE 8000
PC connected to the JACE , graphics complete
On web browser several pages are...

I connected to it with a micro USB.
It powers up and everything. THE BST , had very limited
Functionality. BAUD rate ,Device ID , but nothing much more.
I downloaded the Trane Tracer TU...

Yes 3.2, At our support site,That was the only 32 bit version
I was able to download. To add to the problem , it changed my host ID, and I had to submit that so the license would
Be valid.
I...

I go back to the site next week
You are saying if I have the 64 bit LDV driver, I can use my 64 Bit Ax workbench?

No, existing standalone controller
That is being replaced by us
Customer does not deal with Trane a ymore

One bench top Trane UC 400.
Connecting to BACnet link point with
Contemporary Controls BACnet router.
It is working great with all Bacnet devices at this site, except with this Trane UC400
On UC...

Do I Still need a 32 bit Version Of Niagara AX or N4?

Lon where are You?
Troubleshooting Lon network segments without an AX Jace
U10 USB Network Interfaces
I am properly running 32 Bit Windows 10 and 32 Bit Web AX 3.2 but the Open LDV 5 Is 64 Bit...

I have a Station that Fails to Open On local PC
I want to stream the Output Log to a text file to save it and see why Application Fails
I click Stream to file, But Under Documents My blank text...

AX 3.8.38. Both Laptops less than 6 months old

Same problem. On Two Laptops, Aways sent over to Java download page, for Version 8
Niagara Web ,Launcher, it locks up while loading modules from remote Jace.
On Andriod tablet it works...

Installed the "M Tools" CD ,
On virtual machine with Windows 10 - 32 bit. So far so Good.

Yes I am running Version 5.4. M-Tools Under Window 10 32 Bit. But There Is no Pass thru Mode Tool.The tools are available except Passthru and I cannot commission the DX through the sire Management...

Excuse me we are running, Metasys site management portal , that is where I need to install Mtools

JCI launcher running ,OK, on a PC with a virtual machine and Windows XP
Is it possible to have M Tools installed or at least discovered by JCI launcher when field devices is clicked on.
Currently...

on a couple of our PC's after selecting "Use Java webstart" and entering our login credentials , we are always
Redirected to the Java Download site. The PC's all have the latest version of Java.The...

I want to drop in a CAF file into a Johnson PCG controller, without re terminating leads
the Honeywell spyder tool has the terminal assignment view to assign points to actual pins.
Is there a...

Yes ,Sensor actuator bus I already have a jack for that
What is "MUT" ?

anyone have the pin Out diagram for the RJ-11 Jack.on the Johnson MAP 1810 gateway
I would like to test or web page configure a couple without pluging it into Johnson controller.
Are they 5...

Discovered a site with some Working Honeywell R2 JACE 501 and 502’s. They are on their own network ,separate from the the N4 and AX JACE’s
Any one have documentation?
Will AX workbench work with...

was told never use any thing other than 20K temperature Sensors,with Spyders
Have two Spyders where 10 K sensors were used,with a tabular conversion extension for each one.
The data was entered in...

We were told to use and older version ,no higher than 10.3 with the BTCVT tool
The MAP gateway is better.

A null or stale value means that nothing is physically or properly connected to the point?
What is a nan value

Yes, physical location of the only JACE ,and Switch, as in ,handheld Netgear switch. I Plug my N4 PC , the supervisor PC and the network cable all into the same Netgear switch.And the controllers are...

No one Knows where the JACE is on this ,limited access ,Site. Four floors and we looked in about ten places.
I am connecting with a Switch."Find Stations" produces no results,it rarely does.
The...

At a site where wire shark is Picking up multiple IP's, Multiple Networks
The station is only available through the Web browser HX PX View, no other views
No AX nor N4 software on local PC
Can...

Installed OpenLDV 5 Network Driver
Installed and Fully Enabled .net Frameworkk 3.5. and 4.8
Rebooted twice.
My usb connection shows "Echelon USB Network Interface"
Eschelon website "The OpenLDV...

New ,Non N2 protocol controllers need the prn file if they are talking over an N2 bus.
Does this mean on a bacnet mstp only network I can discover ,edit and add JCI controllers with Fx Workbench...

Gateway? Good point, when I return to site , I will check it.
I usually have Laptop gateway address set to whatever I need to connect to the internet.
Usually this is the gateway “ipconfig”...

New to Johnson and the PCV controller
The PCT software generated a config file with .PRN extension.
I gather with. .prn file and JCI Import Manager this saves time of manually adding each point...

This has Happened several times already
I can connect N4 Laptop to JACE 8000 Secondary Lan port
Can Connect to Secondary Lan port, 192.168.1.140
Can Not connect to Primary port Neither through...

I was sent two Niagara N4 Station Backups.I renamed the .dist file to a Zip file.Extracted the file. The config.bog file is visible in Windows File explorer.
When I browse with the station copier,...

Theses modules are still working good.If they fail, the owners are still able to get them on E-Bay.
Will the JACE’s and Spyders last as long ?

Has anyone ever heard of a controls company in Fairfield New Jersey called AME?
I have a Job interview that they already postponed two times.
I realize they are a Honeywell distributor, but that is...

Trying to identify what points are associated with what Honeywell Excell input / Output controllers
XL online shows the points and their names, but list each one
With the following reference...

C:/Honeywell for Webs. There are many folders there. Did not find any with an .exe extension
Incidently , Numbawnfela, your replies are always very informative.