Search:

Type: Posts; User: eclipse98

Search: Search took 0.01 seconds.

  1. Just wanted to thank everybody for your excellent...

    Just wanted to thank everybody for your excellent advise and help -- changed 176 to 2 and everything works perfectly -- no more problems with heat pump switching to aux heat and back -- all "missing"...
  2. Sonicview, Thanks for advice, I am going to...

    Sonicview,

    Thanks for advice, I am going to contact my installer for sure and get their input -- what seemed like a simple balance point change turns to be a bigger issue of improper initial set...
  3. Beenthere, I have: 172 - 2 (Heat pump) 176...

    Beenthere,

    I have:

    172 - 2 (Heat pump)
    176 - 0 (can this be a problem ?)

    Options 200 or 210 don't even show up, which explains why backup heat never kicks in. :( Should I change them or...
  4. 342 does not have 2 setting -- I set it to 1...

    342 does not have 2 setting -- I set it to 1 (remote sensor) -- I suspect it is not the cause of the problem as even with E (Auto Discover) option I was getting outside temperature readings. Anything...
  5. Sonicview, I set 342 to 1 (Remote Sensor) but...

    Sonicview,

    I set 342 to 1 (Remote Sensor) but I still can't see 350/360 settings -- can there be any other setting missing that will make 350/360 dissapear ? I can see outside temperature on...
  6. Sonicview, thanks for information -- I have...

    Sonicview, thanks for information -- I have VisionPro AIQ, I am not sure what series -- this is Installation Guide (exactly what I have) from Honeywell web site: ...
  7. VisionPRO IAQ -- need help with programming !

    Hi All,

    I have dual fuel AmSt system (NG furnace/heat pump) -- when it was installed I believe my contractor set balance point (not sure if I am using the right word, this is when heating is...
  8. Replies
    15
    Views
    1,063

    Thanks for the info ! Based on my...

    Thanks for the info !

    Based on my NG/Electicity rates ($1.025/10c) it appears that it is cheaper to use NG when COP drops below 2.7 -- I can assume that Trane/A-S COP numbers should be pretty...
  9. Replies
    8
    Views
    4,774

    I would strongly suggest you read this technical...

    I would strongly suggest you read this technical white paper (go to Independent Testing Results for the Top Rated EAC's):
    http://www.aprilairecontractor.com/products/category/air_cleaners
    ...
  10. Replies
    15
    Views
    1,063

    Guess I can't complain :)

    Guess I can't complain :)
  11. Replies
    15
    Views
    1,063

    Does it mean my filter is a keeper ? :cool:

    Does it mean my filter is a keeper ? :cool:
  12. Replies
    15
    Views
    1,063

    Fair enough :) I wish VisionPro would allow...

    Fair enough :)

    I wish VisionPro would allow changing this tempearture in one degree increments, that would allow more precise level of control, oh well.

    Having said that, is there any...
  13. Replies
    15
    Views
    1,063

    Aircleen 1500 is not washable -- you supposed to...

    Aircleen 1500 is not washable -- you supposed to change media every 3 months. Does it qualify for the best ? :)
  14. Replies
    15
    Views
    1,063

    Wow, under 100 watts corresponds to about...

    Wow, under 100 watts corresponds to about $2.52/month electricity cost (at 10c per kWh), so this is obviously not an issue :)

    I can try 35F, but how do I find out if I am doing the right thing ?...
  15. Replies
    15
    Views
    1,063

    New equipment installed -- need help !

    Hi All,

    Just had my HVAC system installed the other day and have lots to learn -- I have some questions, I am pretty new to all this so go easy on me :)

    New set up (I live in Parker, CO,...
  16. Replies
    12
    Views
    999

    I found some contractors with ServiceMagic, some...

    I found some contractors with ServiceMagic, some of them have very high ratings. But then again, they are rated by a J6P on how punctual they have been, etc. More and more it seems like a gamble to...
  17. Replies
    12
    Views
    999

    Existing system (12 yr old Rheem single speed 80%...

    Existing system (12 yr old Rheem single speed 80% furnace) works "fine", but it is getting older and less efficient, uses archaic humidifier. I am upgrading to high efficiency 2-stage natural gas...
  18. Replies
    7
    Views
    3,124

    EverettsHVAC, Thanks for the good advice ! How...

    EverettsHVAC, Thanks for the good advice ! How would I go about finding a reliable and knowlegeable instaler ? Any good websites with reviews ? :)

    2old2rock, The system we are talking about is...
  19. Replies
    12
    Views
    999

    How to find a good contractor !

    From everything I've been reading on this very informative forum it is becoming pretty clear that having your HVAC installed properly is just as important as quality of the HVAC itself.

    How would...
  20. Replies
    7
    Views
    3,124

    Need advice on Armstrong furnace/heat pump

    Hi Everybody, first post here so go easy on me :)

    I am in the process of replacing 12 year old Rheem furnace (80% efficiency) with 96% furnace/heat pump -- one of the contractors I really liked...
Results 1 to 20 of 20
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event