Search:

Hi' guys I have a problems with the Screw Compressor DXS39 OK' the Slide valve no goes more than 38 to 41 Steps'' never goes full load'' any idea'' Thanks'' oop'' water temp'' ok' pressures ok''

Hi'' We had a problem with screw compressor DX39'' the problem is'' high oil pressure'' Example; We have 300psi high oil pressure and 230psi discharge pressure'' I think someone put to much new Oil...

If you has no problems with Voltage'' Then you has some problems with ohms, Check compressor main power' with compressor full load, and see the Amperage. And check all trasformers ohms.

Check ''Thermistors ohms'' and clean wire thermistors contact with the compressor block''

Check all Jack/ plugs'' ''some wire'' ''some fuse port,,for chiller vibration .

Hi' My friend oK'' if the reading of amprove is correct with the display reading. Then check your Slide Valve torque'' Maybe someone touch or moved the slide valve with the hands'''' I'am sure that...

I have that book,with all that you need'' I from Puerto Rico island and my personal e-mail is juanlandy@yahoo.com for any aditional inf. Excuse my inglish''

''Hi friend, I think you has a little problems' like me'' I from Puerto Rico and I read sometime the same paragraph to understand'''jajajajajajajajajajajajajaja'' Que problema verdad, yo trabajo esos...

Hi'' guys. I have some problems with the Display on York centrifugal chiller model YK . ok the problems is because the display goes on and off,and some distortion on the display. the history read...

check all sensor for that unit,,

If you has that problems'' in some where the compressor force too much'' Clean all condensers'' some problems with fans conderser stages''

If loading or unloading problems occur,use these trouble-shooting steps to hepl identify the problem. #1 WILL NOT LOAD (Micropanel display indicates' STEPS=75) ''Apply 12 VDC to the capacity...

Someone put so much refrigerant in the system'' so much ref' so much oil move'' and the oil block the capilary tube'' OK"" evacuate or remove all refrigerant of the system and flush all system'' do...

Let me see if i on hte stand your question'' you mean (supply sensor and return sensor temp on the chiller loop'' what you whant to know? sensor Ohms''

Hi'' I only whant to know,the formula for cfm,, Example: I have a York Curbpak Air Handling Unit 50hp, 1750rpm 460volt pulleys sizes (motor p 6'') shaft p 10'' how i obtein the cfm thanks

Hi'' friend''''''' where I can fine a Compressor (Clutch ) for Honda civic LX 2001 I need only the Clutch,, any help''please my e-mail is :

Give me all pressure''' disch'' P suct'' P more inf''

nameplate'''

Hi; Friends'' Someone can tellme the difference between' stopper valve and TXV.

check' all sensors values''

Hi'' guys This is the question'': We have York air cooler liquid chiller model# YCAJ98XV6 RECIPROCATING HERMETIC' The situation is we have 3 in superheat and 6 subcooling' suction 70psi dish...

Not Glycol in system'' if I put sepoint in 42deg I has problem,because beging to load and unload the compressors, and The history said LOW CURRENT some compressors 'That is the reason I put the...

Model # YCAS0440E screw chiller 4 compressors'' The 10'in pipe or by-pass is connected approx 23'f from the leaving water of the chiller. This pipe is connected direct one with the other pipe' (the...

chiller L.W.T 42 and R.W.T 44.5 or 45 not more than 4deg OK"" the I have about 9 ot 10 ahus, "Ent Water temp 43 ,44 and leaving the coil, someone 50deg or 51deg Not more''

York tech' tell me the I has 15 psi, between L.W and R.W and he tell me no problems with balance, but hmmmm