Search:

Type: Posts; User: fishnfool

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    35
    Views
    3,406

    I have seen one exhaust vent that has froze here...

    I have seen one exhaust vent that has froze here in Ga. it was on top of a mountain in Ellijay under very extreme cold and windy conditions!
    The blocks used under the furnace are foam blocks and...
  2. Thread: Ruud or Heil

    by fishnfool
    Replies
    6
    Views
    1,270

    I agree limited info. I am a Ruud dealer, you...

    I agree limited info. I am a Ruud dealer, you will not go wrong with Ruud BUT it doesn't matter what type of equipment you use if you do not have a competent installer or if you go with the cheaper...
  3. Replies
    507
    Views
    18,497

    After looking back and seeing this is a mobile...

    After looking back and seeing this is a mobile home install,the dripping is actual blowout from the high static pressure. I will go out on a limb and say that coil is not rated for the static...
  4. Replies
    507
    Views
    18,497

    Dripping problems?

    Dripping problems?
  5. Replies
    8
    Views
    3,129

    All most homebuyers are interested in are the...

    All most homebuyers are interested in are the granite countertops and floors its almost sickening to see them spend $$,$$$. On countertops and complain about the hvac being $,$$$. trying to cut...
  6. Replies
    507
    Views
    18,497

    ROFLMAO :D

    ROFLMAO :D
  7. Replies
    507
    Views
    18,497

    I have said above and still hold to it, my money...

    I have said above and still hold to it, my money is on the sweat joint on the liquid line at the condenser or scale build up in the screen @ the txv!;)
  8. Replies
    4
    Views
    364

    Ummm unless that old Borg Warner is a 13 seer...

    Ummm unless that old Borg Warner is a 13 seer coil (NOT) you are going to have some serious problems that nobody will be able to help you with. Do yourself a favor get the new coil!
  9. Replies
    507
    Views
    18,497

    I am still putting my money on a brazing related...

    I am still putting my money on a brazing related problem here. He more than likely did not use nitrogen while brazing, either the screen is stopped up @ the txv or they ran to much solder into the...
  10. Replies
    24
    Views
    3,408

    I wish all Hvac companies and homeowners...

    I wish all Hvac companies and homeowners understood this! Not saying all that work for these home warranty co. are bad but around here I haven't seen the good ones yet!
  11. Replies
    10
    Views
    713

    If you vaporize it you are putting the moisture...

    If you vaporize it you are putting the moisture back in the air = humidity! You can use a condensation pump to pump the water outside.
  12. Replies
    507
    Views
    18,497

    You say the brazing looks crappy for you to say...

    You say the brazing looks crappy for you to say that it really must be bad. It is possible they have partially blocked the liquid line with solder!
  13. Replies
    8
    Views
    916

    Technically with it being within the same...

    Technically with it being within the same envelope yes. But the main problem is there could be humidity issues due to lack of airflow in those rooms. These issues will or should be noticed by any...
  14. Replies
    18
    Views
    968

    Give the guy a chance to check it out before you...

    Give the guy a chance to check it out before you get nervous! It could be something minor that you are not explaining correctly. From what you are describing it is more than likely a factory related...
  15. If that return on the right is the only return...

    If that return on the right is the only return going to that unit you are definitely undersized on duct work!
  16. Thread: Smelly a/c

    by fishnfool
    Replies
    10
    Views
    542

    That is definitely your problem then. Make sure...

    That is definitely your problem then. Make sure you keep water in the tub, shower and sink traps and all smells should leave for good!
  17. Replies
    7
    Views
    2,088

    Out of balance or has a piece of trash in the...

    Out of balance or has a piece of trash in the blower wheel! It doesn't take much. Also I have been to a few 1-2 yr old systems lately that the hub and blower wheel were not pressed tight from the...
  18. Thread: Smelly a/c

    by fishnfool
    Replies
    10
    Views
    542

    Is this bath used by any chance? If the tub or...

    Is this bath used by any chance? If the tub or sink is not used you probably have a dried out trap, happens alot in houses that do not use the upstairs bath!
  19. That would depend on if it is flex or metal, 20...

    That would depend on if it is flex or metal, 20 6''Flex @.1 will leave you 360 cfm short for a 5 ton system!
  20. Replies
    46
    Views
    4,429

    Remember when you were a kid and run the string...

    Remember when you were a kid and run the string thru two cans so you could communicate. Apparently the mall can't afford radio's! LOL
  21. Replies
    0
    Views
    384

    Has anyone heard of

    a company called Modern Metal Arts or Future Challenger that make display doors for walk-ins? I am needing some door parts for a customer and I can not locate any info on them at all, they were out...
  22. Replies
    19
    Views
    1,176

    Doing the returns is the right way you will not...

    Doing the returns is the right way you will not regret it!
  23. Thread: egg heads?

    by fishnfool
    Replies
    4
    Views
    1,184

    I know this is old thread. There is nothing to...

    I know this is old thread. There is nothing to dislike. They are great and I will never be with out one.
  24. Replies
    17
    Views
    13,514

    here ya go! ...

    here ya go! http://www.rmsgas.com/cr417aoverview.htm
  25. Replies
    7
    Views
    4,509

    U= Ruud B= Blower unit H= Air handler A=...

    U= Ruud
    B= Blower unit
    H= Air handler
    A= Design series
    24= Cabinet width
    J= 1 phase
    11= 10.5kw heat strips
    N= No circuit breakers single supply circuit
    H= Horizontal left front...
Results 1 to 25 of 48
Page 1 of 2 1 2
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event