Search:

Type: Posts; User: leakcheck

Page 1 of 5 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    52
    Views
    4,966

    Incoming emails for hotrodrob and Trucontrol in...

    Incoming emails for hotrodrob and Trucontrol in case you didnt get it yet also. Its a great document
  2. Replies
    12
    Views
    379

    May I also get a copy please ?

    May I also get a copy please ?
  3. Replies
    7
    Views
    576

    I had 4 of these that mitsubishi came and setup....

    I had 4 of these that mitsubishi came and setup. Had to write a bit of logic in the jace to make occ/unoc heat/cool setpoints from a single setpoint system. After a bunch of trial and error finally...
  4. Comm 4 driver for chillers with UCP2 boards

    I have a couple Trane chillers with UCP2 boards that I have to integrate into a Vykon Jace by using the Comm 4 driver. I read the pamphlet that came with the driver, and it said to verify the address...
  5. Replies
    17
    Views
    1,381

    May I also get a copy of this information please...

    May I also get a copy of this information please Digo . It would be greatly appreciated, or if someone that has gotten it would pass it along that would great!
  6. Replies
    14
    Views
    761

    Wow thats a good bit of information. I was...

    Wow thats a good bit of information. I was wondering why in BACnet, my copy paste of points for my FX-PCGs would all error out. This will make my life easier.
    Thanks guys, I will give it a try...
  7. Replies
    8
    Views
    564

    I would also be interested in your guide. My...

    I would also be interested in your guide. My email is in my about me page if you click on my name to view my profile.
  8. Replies
    4
    Views
    231

    That's what I did for the first to AHUs they are...

    That's what I did for the first to AHUs they are back to back to an OA plenum 2 climate changers from the late 90s. But its tough to figure out what sensors are for what AHU being they only use 1...
  9. Replies
    18
    Views
    703

    I will send you an Email titled UPCM GET. I know...

    I will send you an Email titled UPCM GET. I know they dont like it much if you post emails in the forums. Thanks again Calder!
  10. Replies
    18
    Views
    703

    Actually ended up getting it and a programming...

    Actually ended up getting it and a programming guide from a guy at work thanks for the offer!
  11. Replies
    18
    Views
    703

    Thank you soooo much. I havnt received it if you...

    Thank you soooo much. I havnt received it if you sent it. If you havnt gotten time no rush just letting you know it didnt go through if you did.
  12. Replies
    18
    Views
    703

    Is there a possibility I could get a copy of this...

    Is there a possibility I could get a copy of this program also please. Need a way to get a points list.
  13. Replies
    4
    Views
    231

    It has tracer summit. not sure on the version...

    It has tracer summit. not sure on the version though its from the late 90s.
  14. Replies
    4
    Views
    231

    Trane UPCM to PCG

    Hi,
    I am trying to change out several AHUs using UPCMs to run AHUS they have 2 AHUS per UPCM and have probably a dozen inputs and 8 or 10 outputs total between the 2 AHUS.
    If I can look on Summit ...
  15. Replies
    3
    Views
    377

    You will need to put the prn files on the jace...

    You will need to put the prn files on the jace and then use the discovery and find the prn file or dmo if its a dx9100.
    If you do not have the prn file then you will need to get them from the...
  16. Replies
    3
    Views
    307

    Yea priority slot 8 is reserved for the override...

    Yea priority slot 8 is reserved for the override function and Is not writable at least on a vykon asside from the override.
  17. Replies
    3
    Views
    377

    vykon Jace 700 N2 issue

    I have a Vykon Jace 700 with a N2 trunk (Ibms-N2 driver) and some of the VMA' s on the trunk share a Zone sensor. When I link mark the ZN-T they work fine but the randomly get a exceptionCode#0 in...
  18. Replies
    13
    Views
    407

    I ended up using a oneshot tied to release all to...

    I ended up using a oneshot tied to release all to the false command of a numeric switch.
  19. Replies
    13
    Views
    407

    Thanks guys this worked perfect writing to a...

    Thanks guys this worked perfect writing to a higher Priority with it as a numeric writable.

    The only other issue I was having is that I am trying to send a command to the Heat Valve on a Warm_up...
  20. Replies
    13
    Views
    407

    Thanks for the help guys

    Thanks for the help guys
  21. Replies
    13
    Views
    407

    Ok cool tonight ill have to give that a try. I...

    Ok cool tonight ill have to give that a try. I might not have been using a high enough write priority when I did it originally. I was attempting to write at 16. And it would go orange with a write...
  22. Replies
    10
    Views
    433

    Good for you man keep it up! All I can say is...

    Good for you man keep it up! All I can say is just dont get discouraged even when things add several more greys to the beard and less hairs to the head!

    I am also new to the controls trade and was...
  23. Replies
    13
    Views
    407

    When you say to add the point as an iutput do you...

    When you say to add the point as an iutput do you mean to just add it as a numeric writable? I dont think I can change the AI to an AO persay since the address is AI. I understand what you mean with...
  24. Replies
    13
    Views
    407

    Dang got a read fault on those points. Thanks for...

    Dang got a read fault on those points. Thanks for the try.
  25. Replies
    13
    Views
    407

    Awesome thank you I, will try this. I tried the...

    Awesome thank you I, will try this. I tried the sp high and low at adf 127 and adf 128 but this sounds more promising. Thanks a million
Results 1 to 25 of 125
Page 1 of 5 1 2 3 4
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event