Search:

Type: Posts; User: IceDoctorII

Page 1 of 2 1 2

Search: Search took 0.01 seconds.

  1. Replies
    15
    Views
    755

    Freeze ups may not be warranty depending on...

    Freeze ups may not be warranty depending on cause. If caused by not being cleaned in 2 years - lots of luck.
  2. Replies
    19
    Views
    1,104

    Try Q320. Y denotes cube size.

    Try Q320. Y denotes cube size.
  3. Replies
    27
    Views
    1,771

    Did you mount the TXV with the dome up?

    Did you mount the TXV with the dome up?
  4. Replies
    26
    Views
    1,040

    High pressure control is in series with contactor...

    High pressure control is in series with contactor coil. High Temp Safety is wired with harvest area.
  5. Replies
    26
    Views
    1,040

    Don't know why the contactor would trip but have...

    Don't know why the contactor would trip but have seen the harvest motor attempt to run backwards which would cause the harvest to last about a half a second.
  6. Replies
    46
    Views
    3,552

    If you are in a small town or rural area be...

    If you are in a small town or rural area be prepared for both. HVAC becomes more refrigeration every day.
  7. Replies
    7
    Views
    446

    Don't guess - check sequence of operation and...

    Don't guess - check sequence of operation and find what is not happening. I would pay special attention to the high temp safety.
  8. Get used to it-deal with it or change...

    Get used to it-deal with it or change professions. It's part of commercial service.
  9. Replies
    33
    Views
    2,718

    You expect a tech to admit he made a mistake? ...

    You expect a tech to admit he made a mistake? Only old geisers who have nothing to loose will admit to have done something less than perfect.
  10. Replies
    18
    Views
    1,080

    Sounds like the magnet broke off leaving just the...

    Sounds like the magnet broke off leaving just the stem remaining. It is about 3/8
  11. Replies
    21
    Views
    2,247

    Don't call the machine names - it will just get...

    Don't call the machine names - it will just get even. After cleaning the probe including the plastic- rinse it thoroughly in fresh clean water and reasonably dry including the wire and your problem...
  12. Thread: Aspen 416

    by IceDoctorII
    Replies
    10
    Views
    1,240

    Who does it help when it is only cheaper? Use...

    Who does it help when it is only cheaper? Use what works and stick with it. The customer respects you more for quality than cheap.
  13. Replies
    33
    Views
    3,673

    HP81 replaced 502 in Manitowoc ice machines. ...

    HP81 replaced 502 in Manitowoc ice machines. Dupont MP39 for R12 AND CHANGE txv
  14. A lot of vital parts have been discontinued for...

    A lot of vital parts have been discontinued for the undercounter B models take care not to thro good money after bad.
  15. Replies
    14
    Views
    1,304

    300 is a long way from 1400.

    300 is a long way from 1400.
  16. Thread: Manitowoc

    by IceDoctorII
    Replies
    13
    Views
    1,681

    I would suggest thoroughly checking/replacing the...

    I would suggest thoroughly checking/replacing the on-off switch. When they get bad connections internally they can cause wierd/ intermittent problems.
  17. Replies
    11
    Views
    1,266

    I bet it mostly happens on fridays at 4pm!

    I bet it mostly happens on fridays at 4pm!
  18. Replies
    20
    Views
    1,977

    You can do a lot of things that you think will...

    You can do a lot of things that you think will fix the problem but the simplest solution is to raise the water level to 1/2 in above the water pump and put the front panel back on. The problem will...
  19. Replies
    6
    Views
    618

    The "B" machine is older style with a float valve...

    The "B" machine is older style with a float valve where as the "Q" machines are batch fill and more water efficient.
  20. Replies
    62
    Views
    3,554

    Try drying off the evap with a heat gun to check...

    Try drying off the evap with a heat gun to check for scale. Check and make shure the weep holes are not plugged.
  21. Replies
    31
    Views
    2,248

    Did you use all OEM parts? (Compressor, TXV, Fan...

    Did you use all OEM parts? (Compressor, TXV, Fan Cycle and LL drier)
  22. Replies
    10
    Views
    1,131

    Kinda like PPV.

    Kinda like PPV.
  23. Replies
    20
    Views
    3,885

    my advise - go it alone and be careful of who and...

    my advise - go it alone and be careful of who and if you give credit.
  24. Replies
    18
    Views
    1,910

    how about turning the water off to the machine...

    how about turning the water off to the machine after the second fill until it enters harvest?
  25. Replies
    23
    Views
    2,287

    Does it have a defrost termination thermostat?

    Does it have a defrost termination thermostat?
Results 1 to 25 of 37
Page 1 of 2 1 2
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event