Search:

Type: Posts; User: MrYork

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Thread: York Impeller

    by MrYork
    Replies
    4
    Views
    912

    York Impeller

    Good day to all. I hope the summer has been hot enough for you all. I am doing a rebuilt on a York YDTL-120. When I recovered the refrigerant from the unit there was water in the refrigerant(found...
  2. Thread: York YK

    by MrYork
    Replies
    8
    Views
    899

    Hvacr update your email and I'll send you one.

    Hvacr update your email and I'll send you one.
  3. Thread: R-12 AC Unit

    by MrYork
    Replies
    21
    Views
    1,908

    Hot-shot works the best. R409 was one of the...

    Hot-shot works the best. R409 was one of the first drop ins I've used both and by far hot-shot works best, lower discharge theps and lower discharge pressures.
  4. Replies
    11
    Views
    1,027

    Just work on my first style G. i like some on the...

    Just work on my first style G. i like some on the changes. modbus communication from the VSD and the integration of the ACC board into the 2430 board should eliminate some of those com faults. (Like...
  5. Replies
    14
    Views
    1,310

    Thank I'll look into that.

    Thank I'll look into that.
  6. Replies
    14
    Views
    1,310

    I'm embarrest:o I don't get many requested for my...

    I'm embarrest:o I don't get many requested for my picture:D:D Just kiddin I'll take some pics, of the compressor.
  7. Replies
    11
    Views
    811

    I emailed you what i found. You should be able to...

    I emailed you what i found. You should be able to order through Baltimore parts.
  8. Replies
    11
    Views
    811

    I got a pretty good breakbown somewhere, ill look...

    I got a pretty good breakbown somewhere, ill look tonight. Not too much you can do to them in the field.
  9. Replies
    14
    Views
    1,310

    Yup!!! Slide valve it is,:( The slide valve rod...

    Yup!!! Slide valve it is,:( The slide valve rod is gone too.:eek: Does anyone have service bulliten sbc9908? already ordered part RCD suggested.
  10. Thread: YCD600A VAV RTU

    by MrYork
    Replies
    2
    Views
    855

    Should be...

    Should be here.http://www.trane.com/Commercial/LiteratureSearchList.aspx
  11. Replies
    14
    Views
    1,310

    Tried 1279s Idea, no luck:confused::(.Well...

    Tried 1279s Idea, no luck:confused::(.Well recover refrigerant and tested solenoids, found the unload solenoid leaking so we both of them. Removed the oil supply line and the oil return line and...
  12. Replies
    12
    Views
    8,771

    What style of chiller, post Model# and post your...

    What style of chiller, post Model# and post your email address on your profile and I'll see what I can get. If i don't have it I know 56 or K will.
  13. Replies
    14
    Views
    1,310

    23xl will not load

    Carrier M#23xl4343nd60 Ser#4996j55208 Chiller will not load up. After reading some old threads My best bet would be a leaking slide valve. I already ordered the load and unload solinoids. Called...
  14. Replies
    3
    Views
    810

    Bard makes a wall mount unit thats single phase,...

    Bard makes a wall mount unit thats single phase, you might want to check with them.
  15. Replies
    4
    Views
    710

    Ya had this problem a few times. We found that if...

    Ya had this problem a few times. We found that if your short on charge the discharge gas will flow through the head master valve for extended periods of time causing the valve to seize in the bypass...
  16. Thread: RTAA fault

    by MrYork
    Replies
    44
    Views
    5,617

    Now that's how you post!!!, short, conscience and...

    Now that's how you post!!!, short, conscience and to the point.
  17. Replies
    6
    Views
    604

    We install non fused disconnect after making sure...

    We install non fused disconnect after making sure your main breaker is properly rated, if not then a fused disconnect should be used. regardless if the drive likes it or not safety and code...
  18. Replies
    11
    Views
    1,452

    I know where your going with K. I have a big...

    I know where your going with K. I have a big problem with post (almost always by newbies) That ask a question then have highly trained professionals (some factory trained)bend over backwards to try...
  19. Replies
    3
    Views
    552

    You might take this opportunity and sell them on...

    You might take this opportunity and sell them on a PM contract. then maybe you can work something out on the repair cost. Leasing ice makers can be very profitable.
  20. Replies
    6
    Views
    1,818

    From your post i'm assuming you took thoes...

    From your post i'm assuming you took thoes reading when the drive was in the run state, If this is the case than your missing the ground on the VSD enable. En will go to ground when in the run state....
  21. Replies
    68
    Views
    4,148

    I think Sammy's concern is more for his...

    I think Sammy's concern is more for his reputation and cash flow than the fact that he's going to work harder while his help is on Vacation, and in a small town sometimes your reputation is your...
  22. Thread: Slide valve

    by MrYork
    Replies
    20
    Views
    1,309

    :o:o Ya I knew that!!!!:) But I though he was on...

    :o:o Ya I knew that!!!!:) But I though he was on restriction;)
  23. Thread: Slide valve

    by MrYork
    Replies
    20
    Views
    1,309

    Wow Thanks JJ, I would go as far as saying...

    Wow Thanks JJ, I would go as far as saying everyone that particpates in this forum is important....including yourself. As for your response I'm not sure what theses other guy are talking about, I...
  24. Replies
    15
    Views
    5,841

    Here in Texas everyone has a gun, Including our...

    Here in Texas everyone has a gun, Including our pets:D This cat can shoot a tic on a Bores bacfkside at 300 yards with the wind blowing 25mpr while eatin catnip. ya I like this site too, Just goes to...
  25. Replies
    15
    Views
    5,841

    I was talking about a Hatfield and McCoy feud. Or...

    I was talking about a Hatfield and McCoy feud. Or Mississippi and Alabama feud. None the less never mind.:o...Just my Alzheimer kicking in again.
  26. Replies
    15
    Views
    5,841

    How about it Klove.... can you help your neighbor...

    How about it Klove.... can you help your neighbor out or is there some kind of feud going on?..:)
  27. Replies
    14
    Views
    1,485

    What's happening up there that would cause you...

    What's happening up there that would cause you gent's to move on?
  28. Replies
    19
    Views
    7,037

    Yes 6 springs are available, however York...

    Yes 6 springs are available, however York recommends you use the Bellow style shaft seal. Although you can replace the seal by bringing up the pressure but then you wouldn't know how short you may be...
  29. Replies
    16
    Views
    2,554

    You didn't post your oil temp? Also check your...

    You didn't post your oil temp? Also check your discharge temp and the temp on the heads. You could also be losing oil pressure on one of your unloaders, load and unload the comp and see if this...
  30. Replies
    14
    Views
    1,485

    Good pay and benniies, (from the union) thats the...

    Good pay and benniies, (from the union) thats the good part, If you like someone looking over your shoulder all the time and listening to your customer complaints about there bill well that's the bad...
  31. Replies
    8
    Views
    591

    Thanks Dutchman, I'll double check connections.

    Thanks Dutchman, I'll double check connections.
  32. Replies
    14
    Views
    1,485

    What I do at sites with multiple chiller is to...

    What I do at sites with multiple chiller is to first print the sales order then the set point then the chiller status, this should work even if your sales order is blank(just modify the blank sales...
  33. Replies
    108
    Views
    6,611

    St65 did you already run off your new...

    St65 did you already run off your new apprentices?:( They looked like females to me.
  34. If I take an Elk out with my van I wouldn't have...

    If I take an Elk out with my van I wouldn't have a van to drive away.
  35. Well you left us hanging.... What did you find...

    Well you left us hanging.... What did you find out, have you logged the chiller? Did you get the problem solved? Also There is JCI branch in El Paso if worst come to worst you can give the a call.
  36. Replies
    27
    Views
    2,325

    O.K AT&T, Go ahead and ask your question again.

    O.K AT&T, Go ahead and ask your question again.
  37. I actually like to hunting or by Reserve N.M nice...

    I actually like to hunting or by Reserve N.M nice big Elk:). If he's around there and It's hunting season I'm there.
  38. I think Varo is feeling a lot like york56's...

    I think Varo is feeling a lot like york56's cat:confused::D.... Varo email me and I'll send you some literature.
  39. I think he's talking about a YS. If that's indeed...

    I think he's talking about a YS. If that's indeed the case then the panel will display Excess charge warning when the discharge superheat is below 15 degrees and depending on the eprom version will...
  40. Thread: Another YCAS

    by MrYork
    Replies
    8
    Views
    595

    There should be a plug on the bottom of that oil...

    There should be a plug on the bottom of that oil separator with an o-ring (02812961006) that I have had to change-out before. I love these machines. Confirm that o-ring part number before ordering.
  41. Replies
    15
    Views
    1,360

    Which one costs more?

    Which one costs more?
  42. Replies
    8
    Views
    591

    Thanks Refer, I got the files and I'll read over...

    Thanks Refer, I got the files and I'll read over them tomorrow.
  43. Replies
    7
    Views
    1,026

    Check your mail. I didn't have a OT manual on...

    Check your mail. I didn't have a OT manual on file but I'll see if i can scan a copy tomorrow. Good Luck
  44. Replies
    8
    Views
    591

    It has a pic I. I'm going over on Friday to...

    It has a pic I. I'm going over on Friday to checkout the ground and electrical connections, You know all the basic.
  45. Replies
    21
    Views
    2,918

    Parked outside my former SOA's house.

    Parked outside my former SOA's house.
  46. Replies
    21
    Views
    2,918

    York56, I like your cat...or is that you in that...

    York56, I like your cat...or is that you in that pic. Haha
  47. Replies
    15
    Views
    1,360

    Check your email and good luck you'll need it. I...

    Check your email and good luck you'll need it. I hate these units. I have had some unit that are nothing but lemons and others that start-up without a hitch and run and run.
  48. Replies
    8
    Views
    591

    23xl loss of comm

    I have a 23xl4343ed60 Ser#3896J54475. This chiller is locking out on loss of communication with starter. This is happening at differant times of day and at low load and peak load conditions. There is...
  49. Replies
    15
    Views
    1,360

    The IOM manual you need is 100.50-nom3(109) I...

    The IOM manual you need is 100.50-nom3(109) I would email it to you but your profile does not contain any emai address. You would have to throw in some K.C and sunshine band tape or Chicago.
  50. Replies
    27
    Views
    2,325

    AT&T tech, if you didn't want anyone to think you...

    AT&T tech, if you didn't want anyone to think you worked for AT&T them maybe you shouldn't have used it as your user ID. Checkout Graham's, Kloves and some of the rest of the members and then you...
Results 1 to 50 of 92
Page 1 of 2 1 2
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event