Search:

Type: Posts; User: heatingairman

Page 1 of 6 1 2 3 4

Search: Search took 0.01 seconds.

  1. Thread: MUNCHKIN

    by heatingairman
    Replies
    9
    Views
    1,375

    Nikki, Where do you live?

    Nikki,
    Where do you live?
  2. Replies
    2
    Views
    1,109

    3 ton, 10 - 11.5 SEER depending on match up.

    3 ton, 10 - 11.5 SEER depending on match up.
  3. GO FOR IT! Put the G71 in your house and move the...

    GO FOR IT! Put the G71 in your house and move the G61MPV to the garage. Just keep the heat above 55 degrees in the garage to reduce the chances of condensing in the primary heat exchanger.
  4. Uh Oh! 3. No pricing questions please Only...

    Uh Oh!

    3. No pricing questions please

    Only people who actually see your job can price it accordingly. There will be no pricing allowed in the public access areas of this site. Please do not...
  5. Replies
    11
    Views
    1,173

    Wave of the future my friend... I guess we'll...

    Wave of the future my friend... I guess we'll see...
  6. Replies
    57
    Views
    12,961

    If it was my house I'd do the G71. Sounds like a...

    If it was my house I'd do the G71. Sounds like a perfect application for that furnace. It's going to run at 40% modulation a majority of the time which is a little lower than the G61V on 1st stage.
  7. Replies
    8
    Views
    7,372

    I like the Fujitsu units. Daikin units are nice...

    I like the Fujitsu units. Daikin units are nice too!
  8. I would stay FAR AWAY from products made by...

    I would stay FAR AWAY from products made by American Water Heater!!! If I were you, I'd consider another product besides the Polaris unit. Have you looked at the Phoenix unit by Heat Transfer...
  9. DuraCURVE:D

    DuraCURVE:D
  10. Most crack because the furnace is oversized and...

    Most crack because the furnace is oversized and the return is too small.
  11. You're not kidding! It almost certain that the...

    You're not kidding! It almost certain that the damper door spring will break, then the flame sensor ceramic will snap, then you have to pull the manifold to get the burners out, then....
  12. LMAO!!! I remember a crawl in Indy where they...

    LMAO!!! I remember a crawl in Indy where they installed an upflow Pulse when it should have been a horizontal. They dug a hole and put the furnace in the uplow position... INGENIOUS and P'O'D me!
  13. Do yourself a favor Jill and call a HVAC...

    Do yourself a favor Jill and call a HVAC Technician. You're dealing with line voltage and gas... Don't take a chance on injuring yourself. NO DIY HERE!
  14. Toughest Furnace for Routine Maintenance

    What's your most unfavorite gas forced air furnace to perform routine maintenance on? You know the feeling you get when you go to a house and set your tool bag down and dread the thought of doing any...
  15. Replies
    13
    Views
    1,062

    Go ahead and use the 3/4 line set. It will void...

    Go ahead and use the 3/4 line set. It will void the warranty that comes with the unit. I don't think the customer will mind. :D
  16. Replies
    2
    Views
    483

    1st stage 67%/2nd stage 100%.

    1st stage 67%/2nd stage 100%.
  17. Replies
    13
    Views
    3,361

    The purpose of staging up is to satisfy the...

    The purpose of staging up is to satisfy the thermostat (or please the customer by keeping them comfortable). What would be the purpose of staging the burner back down if you're trying to satisfy the...
  18. I've seen it before. The terminals let loose on...

    I've seen it before. The terminals let loose on the compressor spewing oil all over and all you need is a little voltage or something hot present. It doesn't seem to be product specific though. My...
  19. Replies
    9
    Views
    1,240

    Amen Brother!

    Amen Brother!
  20. Replies
    106
    Views
    6,734

    When you drive through a neighborhood and you...

    When you drive through a neighborhood and you remember what kind of equipment they have.

    "That house has a Heil NUGK and a tear drop condensing unit"

    "That house has a Pulse and a HS16"
    ...
  21. www.obsoletefurnace.com:D You can't get parts...

    www.obsoletefurnace.com:D

    You can't get parts for those things anymore!

    Does it have a seal balancing a ball on it's nose on the badge?
  22. Replies
    25
    Views
    1,830

    DUDE...... He kinked the copper... How the F do...

    DUDE...... He kinked the copper... How the F do you kink 1/4" copper???? Good thing he doesn't have to run line sets!
  23. Replies
    17
    Views
    1,318

    I sent yo an email too bigjon.

    I sent yo an email too bigjon.
  24. Replies
    17
    Views
    1,318

    I don't think anyone will go out on a limb with...

    I don't think anyone will go out on a limb with 500fpm:D
  25. Replies
    17
    Views
    1,318

    WOW! I hope you don't do refrigeration! OOPS......

    WOW! I hope you don't do refrigeration! OOPS... Read it wrong Beenthere! Need to assure proper velocity Horizontal increase size, vertical decrease.
Results 1 to 25 of 139
Page 1 of 6 1 2 3 4
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event