Search:

Type: Posts; User: COOPE

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    52
    Views
    3,643

    At the school district I work for I had to order...

    At the school district I work for I had to order a new oil level sight glass since the original one was leaking and had a crack. The parts counter guy said "WOW, that thing was built in 1962, that's...
  2. Replies
    14
    Views
    2,145

    Anyone seen my cousin Mike???? Just joking, this...

    Anyone seen my cousin Mike???? Just joking, this is a good example of how we all get a bad name. Even though we would not do this unfortunately it still reflects upon our Industry. Someone should...
  3. Replies
    23
    Views
    2,494

    Found and tightened a union on the drain line....

    Found and tightened a union on the drain line. Re-insulated afterwards. The heat tape was working, checked it with another meter. Sublimation is slowly removing the remaining ice. Thank you again
  4. Replies
    23
    Views
    2,494

    Thanks guys, you've given me some great ideas....

    Thanks guys, you've given me some great ideas. Yea I checked today, the heat tape on the drain line has power but is pulling 0 amps. It is really old so we are going to cut the insulation off, put...
  5. Replies
    23
    Views
    2,494

    Thanks guys, I will try some of the ideas. I am...

    Thanks guys, I will try some of the ideas. I am going to see where it came from. Probably the pan or drain heater. Had a huge chunk of ice coming off from up there. Will have to get one of the...
  6. Replies
    23
    Views
    2,494

    I work for a local school district. It is in our...

    I work for a local school district. It is in our warehouse walk in freezer. I 'm just trying to figure out how to get the last thin layer off the floor, at -10 any hot water will just refreeze...
  7. Replies
    23
    Views
    2,494

    Ice on walk in freezer floor

    This is a general question. How do you remove ice on walk in freezer concrete floor. I used a hammer drill with flat blade bit and got it down to about 1/4" thick with out hurting the floor. I...
  8. Replies
    58
    Views
    3,306

    We used to do follow up calls when we sent out...

    We used to do follow up calls when we sent out direct mail cards. We got away from the letters unless we could personally do the mailing, write the name, address and stamp. If people get bulk mail it...
  9. Replies
    6
    Views
    513

    A lot of the older strips were of larger...

    A lot of the older strips were of larger diameter, some of the newer ones are of a smaller diameter. I always went back with the same diameter string. I am sure you should get them to work somehow....
  10. Replies
    58
    Views
    3,306

    I would not "steal" my former employers...

    I would not "steal" my former employers customers, I have never burned a bridge and have been told by either of them if I ever wanted to return just call and I could start the next day. Back in the...
  11. Replies
    6
    Views
    513

    Will a 5 KW restring kit work. If so you should...

    Will a 5 KW restring kit work. If so you should be able to get that at most part houses. Not fun to do but can be done, Just don't stretch it to much and make sure you replace the fuse link and at...
  12. Replies
    10
    Views
    588

    I think you will be happy with it, good luck

    I think you will be happy with it, good luck
  13. Are you charging in cooling mode? Try covering...

    Are you charging in cooling mode? Try covering the top of the condenser (if top discharge) does the head pressure go up then. I do this to simulate a warmer outdoor temp when it is cooler outside....
  14. Replies
    5
    Views
    540

    I use a small wire brush about the size of a...

    I use a small wire brush about the size of a toothbrush first. If it is an upflow I slide in a pc of cardboard to catch the big stuff then shop vac it out. then use coil cleaner, water, coil cleaner,...
  15. Replies
    6
    Views
    513

    Do you have an ACES distributor in your area,...

    Do you have an ACES distributor in your area, they handle trane parts as well and just might be able to locate one
  16. Thread: resi techs

    by COOPE
    Replies
    11
    Views
    706

    We had those oil filled radiant heaters. We kept...

    We had those oil filled radiant heaters. We kept them in the shop, our delivery guy would deliver them and have the customer sign an invoice showing they had them. When we did the install we would...
  17. Replies
    10
    Views
    588

    I've been in the business almost 30 yrs. From and...

    I've been in the business almost 30 yrs. From and installer, maintenance and service tech. Also was service manager for 13 years. I have everything except an extended wheelbase van. I now work for a...
  18. Replies
    30
    Views
    1,672

    Glad you got it fixed. 4.25" W.C. is high and...

    Glad you got it fixed. 4.25" W.C. is high and didn't help the problem. That could be part of why the roll out failed.
  19. Replies
    16
    Views
    758

    Guys after talking to the Rheem tech rep on the...

    Guys after talking to the Rheem tech rep on the phone again today and both of us looking at the diagram and molex plugs I did have a connector in the wrong spot. I am quick to admit when I goofed and...
  20. Replies
    16
    Views
    758

    I already reversed polarity with no change, and...

    I already reversed polarity with no change, and did check all connections. The tech support guy will be calling me today, I asked him about the molex wire colors and he said if I put the new flame...
  21. Replies
    16
    Views
    758

    This is true, thank you

    This is true, thank you
  22. Replies
    30
    Views
    1,672

    You said you are only getting a 32 degree temp...

    You said you are only getting a 32 degree temp rise, why do you think you have an airflow problem? Just asking.
  23. Replies
    16
    Views
    758

    The original board had no spots on the back, I...

    The original board had no spots on the back, I will check tomorrow. I wonder why I can't see any of the other responses to my initial posts? There were several responses, about 5-6. Now they are...
  24. Replies
    16
    Views
    758

    Sorry guys for some reason I can not bring up any...

    Sorry guys for some reason I can not bring up any of your responses to my initial post, not any of them ???? I checked wiring, plug connections, 122 volts to unit. I did not check voltage from...
  25. Replies
    16
    Views
    758

    Rheem board change out now sensor problems

    Rheem model - RGDG07EAUER serial - CY5D302F18944924
    I am a technician and am really frustrated and stumped by this problem, I know someone out there has had the same problem.
    Initially, before...
Results 1 to 25 of 40
Page 1 of 2 1 2
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event