Search:

Type: Posts; User: bpiatchek

Search: Search took 0.00 seconds.

  1. Where do i find the logic statements?

    I did finally find the point names with UPCM Editor. Thanks for the response though.

    As far as I know the desktop CPU could not communicate with the BCU. Everything is still working in standalone....
  2. Trane Tracer Summit Help (How do I view database off-line?)

    I am hoping someone would be generous enough to give me a helping hand on this. I cannot seem to find a way to view the existing database off-line. What I have here is a bad BCU module causing me to...
  3. Replies
    6
    Views
    435

    How to get to the programming blocks

    How do you get all the way down to the programming blocks? Do i need different software other than ESS?
  4. Replies
    6
    Views
    435

    When entering monitor mode I get this following...

    When entering monitor mode I get this following message:

    "If anything has been changed in format you must do a download. If a download is not done at this time and system 1 is accessed, schedules,...
  5. Replies
    6
    Views
    435

    ESS32 Novar Logic View/Edit Menu

    I am working on a Novar System with a Lingo SE and two Savvy31s. I cannot find a way to view/edit the algorythms or any other program block. Does anyone know what menu to go to in ESS32 to see these?
  6. Replies
    11
    Views
    2,058

    I did recently setup up various trends on the...

    I did recently setup up various trends on the Lingo module. Probably about 30 or so room temp sensors. I have task scheduler on ISCOPE to retrieve these data logs from the Lingo once daily. The...
  7. Replies
    11
    Views
    2,058

    Thanks for the help Orion. I was thinking...

    Thanks for the help Orion. I was thinking firmware as well and was trying to find where I could download it. However, another module on the network is having the same communication problem as well....
  8. Replies
    11
    Views
    2,058

    Novar Lingo SE Communication Problems

    I have a Lingo SE Module with a intermittion comm loss over the facility's network. When pinged it I will got 25% loss, then 30 seconds later a 75% loss, another 30 seconds and a 0% loss. Originaly...
  9. Replies
    2
    Views
    327

    I did find all the data still retained for the...

    I did find all the data still retained for the last two weeks on the module. However, it seems as the the transfer logs operation does not transfer those two weeks when called to transfer. Why would...
  10. Replies
    2
    Views
    327

    Novar Point Trending

    I have set up a trend schedule to have a module record all of the space temps 4 times daily between 9AM to 5PM. I had set this up to run indefinatly. It has been successfully recording for over a...
  11. Replies
    1
    Views
    2,573

    Trane Tracer Summit - Default user/pass

    I just installed Trane Tracer Summit Version 16.00 Demo/Upgrade edition. Does anyone know the defualt username and password? I have searched all through the provided literature and found nothing....
  12. Replies
    1
    Views
    487

    Carrier Comfortview VVT Monitor Stat

    I am trying to upload ( Download ) system parameters from previous controller to newly installed monitor stat. CCN does not give any option to either send or receive programing for only the monitor...
  13. Replies
    2
    Views
    641

    Carrier Zone Controller Error Code

    I have ran into a very odd code displayed on a zonestat controller. I hope this means something to somebody becuase I have referenced it with just about every carrier code I can find.

    mn...
  14. Replies
    4
    Views
    464

    This is a savvy31 module. Would that be a " lingo...

    This is a savvy31 module. Would that be a " lingo " componet? The other values displayed on the service laptop's ISCOPE program fluxuates, so I know at least those have been refreshed. Also, They...
  15. Replies
    4
    Views
    464

    I looks like to me that the graphical screen is...

    I looks like to me that the graphical screen is pointed to the correct point. It reads as "IOI input number 6" on both the graphical screen, all of ISCOPE, and ESS32. I have disconnected that input...
  16. Replies
    19
    Views
    2,160

    Comfortview Start/Stop Program

    Last year I was working for a carrier controls tech for a few weeks on a job we sub-contracted them on. I had comfortview 3.0 and was able to get his copy of 3.1 plus a small program that will...
  17. Replies
    4
    Views
    464

    Novar problem

    I was hoping for some help with a few Novar questions. I have been having to service a new client with Novar controls system and even though I am familiar with many others it seems to have stumped me...
  18. Replies
    9
    Views
    1,495

    Novar PIK bat file

    Does anyone know where I could find the PIK disable bat file?
  19. Replies
    52
    Views
    7,388

    Wow, thanks so much! I would greatly appreciate...

    Wow, thanks so much! I would greatly appreciate it! The ESS programming and IVEW manual are a must have! I added my e-mail address to my profile info. Please send me those as soon as you get the...
  20. Replies
    52
    Views
    7,388

    Novar ESS32 and I-Scope literature?

    Is there any way to find literature on the Novar ESS32 or I-Scope programs? I was hoping someone could point me to a link for a PDF download. I have requested this information on Novar's Controls...
Results 1 to 20 of 20
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event