Search:

Type: Posts; User: coldrig

Page 1 of 7 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    14
    Views
    854

    Thanks for Advice,I will try myself safely If I...

    Thanks for Advice,I will try myself safely If I will see it is not working then I will call Trane Technician.
  2. Replies
    14
    Views
    854

    It was good hint and I tried to adjust Contrast...

    It was good hint and I tried to adjust Contrast but no use I think problem is in circuit,some component heatup because after few minutes backlight disappear.
  3. Replies
    11
    Views
    593

    Thanks for lot of useful information,I will check...

    Thanks for lot of useful information,I will check on Monday and then let you know. VAVs are varitrane.
  4. Replies
    14
    Views
    854

    I got the correct cable and it is communicating...

    I got the correct cable and it is communicating even with old Display although Display screen is blank only backlight but I can
    read all configuration on TechView screen,but I don't see backup
    and...
  5. Replies
    14
    Views
    854

    I am agree with you it is not DIY operation.We...

    I am agree with you it is not DIY operation.We have another same chiller which is working OK so can I take backup from there and load it other Display unit,as it is 100% same configuration.I download...
  6. Replies
    14
    Views
    854

    (Tech View)Is there any restriction like Licence...

    (Tech View)Is there any restriction like Licence or password or it is free to download and use.When I will hookup via serial cable will it read configuration from chiller memory.Then I will restore...
  7. Replies
    14
    Views
    854

    Trane Adaptive Control

    There was Faulty Adaptive Control Display unit on RTAC200 Trane Chiller sticker on backside is X13650827-06 I replaced it with same number X13650827-06 from ebay. when I give it 24Vdc power it shows...
  8. Replies
    11
    Views
    593

    In that setup Screen there is no box to Replace...

    In that setup Screen there is no box to Replace Pressure Dependent to Pressure Independent.
  9. Replies
    11
    Views
    593

    One more question if you can reply,It is showing...

    One more question if you can reply,It is showing Pressure Dependent VAV,Where as these are Pressure Independent VAVs because there are differential pressure transducers,does it make any difference or...
  10. Replies
    11
    Views
    593

    BCU is BMTX and it has Two comm4 links.I...

    BCU is BMTX and it has Two comm4 links.I succeeded to communicate with VAV. As there is no network cable so at the moment I can just connect one by one as required,until we pull cabel. Any how I am...
  11. Replies
    11
    Views
    593

    MP581 is only used for Pumps which is connected...

    MP581 is only used for Pumps which is connected on Comm5 and Chillers are connected on Comm3.At the moment VAVs are stand alone there Built in Cards DDC/U.C.M Control board these are UCM4 and not...
  12. Replies
    11
    Views
    593

    Trane VAV Programming

    We have site with Trane BAS System Tracer Summit Ver16.There are 3 Trane Chillers RTAD and 3 Ch water pump 2 working 1 standby.1 BCU and 1 MP581 Controller.There are few TRANE VAVs are there on there...
  13. Replies
    0
    Views
    224

    VFD-IGBT Question

    Anybody has idea how to check Mitsubishi IGBT PM200DVA120 With Talon VFD Analyzer. Normal IGBT has gate but this IGBT has many control pins. IGBT drawing is attached.Thanks.
  14. Replies
    0
    Views
    211

    SIEMENS VAV PINOUT

    We have Siemens VAVs GDB181.1E/3 with 6 pins for converter connections.Now we receive same Model with 7 Holes for converter connections so AST11 Converter is not communicating.Anybody have Idea how...
  15. Replies
    0
    Views
    207

    SIEMENS VAV static Calibration Question

    Any body have idea how ACS941 Tool calibrating flow rate on Pressure difference.In case of Johnson controls VAV Calibration we need to add Duct size but in case of Siemens VAV there is no requirement...
  16. Replies
    2
    Views
    283

    When I attach HC7410 and try to check DCU address...

    When I attach HC7410 and try to check DCU address it is not showing anything so I don't know how to start communication and assign some address to PCU. Only then it can be possible to download Bin...
  17. Replies
    2
    Views
    283

    I/net PCU7718 Networking problem

    We have problem with I/net 2000 networking ,there are around 25 PCU7718 AND PCU7756 Controllers one of them has some problem due to that all controllers are showing question marks and after few...
  18. Replies
    3
    Views
    420

    Thanks for Default IP,I use same series IP in my...

    Thanks for Default IP,I use same series IP in my PC and I can ping Xenta527 NPR. But I don,t see it online through Inet200 configuration window. What is reason and If I want to change IP of Xenta527...
  19. Replies
    3
    Views
    420

    Tac Xenta527 NPR

    Hi,We have Inet2000 system.I want to configure Xenta 527NPR. According to Manual it can be configured via RS232 cable. Is it possible to configure it via Ethernet cable also. Thanks.
  20. Replies
    0
    Views
    202

    OS2 ULTIVIST UPGRADING

    We have one old site with ULTIVIST on OS/2,Owner want to upgrade their system.There are DMS 350 Controllers. So which software and controllers are most suitable to upgrade this system.Thanks.
  21. Replies
    8
    Views
    898

    Hi Dan

    I will check about backup file,I am not at same site at this time Ithink front end is EBI,let me check it tomorrow
    if you can give me hint about backup file name.Thanks.
  22. Replies
    8
    Views
    898

    Very nice information, We are AC service...

    Very nice information, We are AC service co.Honeywell don't sell us Care software is there any other source from where to buy Care software.Thanks.
  23. Replies
    8
    Views
    898

    SKWSPROUL

    I am thankful to your reply
  24. Replies
    8
    Views
    898

    Honeywell XCL5010 Question

    We have one faulty XCL5010 Controller,When we will replace it with new one is there any programming required or it will upload itself.Thanks.
  25. Replies
    1
    Views
    663

    Tac i/net Seven CD Key

    We have HVAC System with Tac i/net Seven 2.21 installed,There is virus in PC and we want to Format it.We have original CD but Key is not written on it,the person who install it long back left company...
Results 1 to 25 of 168
Page 1 of 7 1 2 3 4
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event