Search:

Water inlet valve finally stuck and identifiable replaced all good

DKM-500BAH serial#E01168J works great only about a month it will have water under neath Ice bin then work great until about another month comes up and then same scenario. It is in a lunch room at...

I received a I phone 6 Plus I can see it perfectly:)

Have you ever done this before? It is not something to just assemble Is this a steam boiler or hot water?

Sure is good to have time stamp on almost all devices.

seems like same unit style I worked on a few years ago but orifices were plugging up causing low pressure the orifices are in the header which you have to replace customer opt for new unit.

suction pressure is up there!

I have a application where they are using a thermal Care roll around chiller M# sq2a0504
The application is on expanders. They place plastic rolls 1 inch across 2 inch long with hole in middle onto...

I went on google to give you the option to read about triple compressor section I obtained something totally different. I am also sorry for Hijack.

Years ago I had installed a gas valve on a package unit with leak lock. Went on vacation and that same valve Failed. When I came back from vacation I received a greeting that I should not use leak...

That is cool

There is just a handful that is different you power o and you will heat.

Lol on losing tools, I still cannot find my $40.00 duracell flash light. 12 volt impact driver works great and light to take screws out of cases and package units or where ever you have more than one...

Pretty nasty Looks like fan shroud is just as bad. I use trash bags and silver tape, open up power box and wrap all with plastic then coil cleaner and water hose followed with shop vac. Tape is to...

You get what you pay for. That said I buy dependable tools, They may cost more but when you need to perform a task you do not want to have tool mar up device or strip a bolt or screw because it was...

Went on a call awhile back at a old folks home, Scotsman flaker ice machine not working. I arrive and see machine disassembled down to gear case is showing grease and water. Maintenance man took it...

Our company installed a duel fuel system, A year later Lightning struck condenser. I received service call they had no heat. When I arrived found Compressor shorted and wiring cooked. Went inside to...

unless you have isolating valves Yes you need to pump it down.

20 years ago I had to change compressor at a drive in movie theater. They was closed I was there alone So I hooked up radio to listen to the Jams while working. Turned on switch and watched it smoke!...

Links to direct purchase sites are not permitted in he open forums.

Normally it is a slightly dirty coil, Water slides down to pan, when you have obstructions on surface water will collect and drop down instead of sliding in pan.

http://www.cornelius.com/ Go to product tab. And what color is your Mice maker:LOL:

With a Robin Air or better . No while it is off, With it running you run the risk of OIL SLUGGING.

Also please explain how I can add oil without losing charge or intro air into sys.

Hand operated oil pump has check valve. place pump in oil container, pump until oil is coming out your...

I`ll second that.

good show

Have you checked your Pump on hydronic side to make sure of circulation. It would be like a restriction in air coil with dirt build up
causing head pressure to do Like what you said. Also Can you...

That rubber plug has cracks been on there quite awhile ago.

Only way this is related to this thread copper tube in compressor shell. Long while back I was given a compressor to change on a unit,
the fan was too close with stub being pointed up. I had to...

For starters you will need compressor, start components, Driers, a lot of screens, If it was a slow burn you will see it through system, I have seen some devices need to be unsweated to clean or...

Also seen where wrist pin would ping against cylinder causing deep grooves.

http://www.hvacfun.com/f-design-refrigeration-syst.htm. At this site it has your dimensions and talking about 800 lb of meat

It maybe mechanically toast. You may need another compressor to start with.

Was at a gas station store there are 8 of them around 50 mile radius. This particular store had Manitowoc Ice machine exact same one in your pics in back room. 400 lb bin, Black mold under evaps and...

http://www.johnsoncontrols.com/content/us/en/products/building_efficiency/integrated_hvac_systems/Industrial___Commercial_HVAC_Equipment/indoorpackaged/watersourceheatpumps.html York in st Louis is...

Just a guess, Have these condensers been split to clean? Awhile back one of our accounts was not keeping up. You could run water through it. split and clean little seeds and strands from plant life.

On start up. Did you weigh in the refrigerant? adding gas as it is running? You have a restriction it may seem, not enough info to see through this monitor of mine.

http://www.fscc-online.com/HIW-Economizers%20(Spring'99)/hiw-economizers.html

Here is some reading material so you can grasp all that you can. I found that at google typing in economizers.

I agree you have to purchase fittings that fit your gauges to there ports.

You need to read the pdf all the way through. Taking note on refrigeration details and All functions of this machine. You will learn, It`s function to make Ice, Also check remote condenser for oily...

Furnace , Evap coil, 2 condenser`s Where is 2 complete older systems in that picture. They need to be junked. :whistle:

Thank you for the lead I do appreciate it :)

Thank you very much I knew someone would know:)

That is a good Idea but I only carry one:grin2:

I need to find an inspection mirror that I can read like I was looking at the Model
#. As it may be 2 inches from wall so I need mirror to read it, It is backwards and sometimes #`s play H*** with...

1-800-5455720 that is the Manitowoc tech line. They are a great help now and then

Are you sure it is not a muffler? Drier in hot gas line will fall apart eventually
then crap in system:gah: I do not believe drier will do it`s job at all

Atv0700110nlt Water Furnace

I cannot remember on a 4 pole contactor physically connected to 3 pole. when 3 pole is pulled in, is that high speed? or 4 pole pulled in would that be high speed. both cannot be pulled in at same...

http://www.spectroline.com/graphics_library_logos.html
Some times The customer wants to see where leak is. I live in the show me state. found multiple leaks with bubbles and detek. when leak is in...