Search:

Type: Posts; User: skpkey9

Page 1 of 17 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    9
    Views
    432

    Stupid question- Have you or anyone else...

    Stupid question- Have you or anyone else checked the switch, while its in it's OFF state when you arrive ? Meaning before touching the switch or anything else.....
    I know you've said you checked...
  2. Replies
    20
    Views
    1,087

    100% disagree. Sorry But Kairak mounts them...

    100% disagree. Sorry
    But Kairak mounts them upside down in their prep tables where the power head is in the condensate pan. Countless units that way, Sporlan valves.
    OP has a different issue. ...
  3. Replies
    10
    Views
    981

    You could do it... With that being said the line...

    You could do it...
    With that being said the line set would need to be sized properly and have all proper traps or you will be replacing compressors, not to mention condenser would need to be...
  4. Replies
    17
    Views
    1,907

    Looks like a black powder measure

    Looks like a black powder measure
  5. Replies
    67
    Views
    3,771

    Ya most likely had a winding to winding short, ...

    Ya most likely had a winding to winding short, if the compressor was wired incorrectly it would be awhile before it shorted the pump.

    Hope this helps.
  6. Replies
    18
    Views
    2,708

    Yes, Supco SS-410. They are made for high...

    Yes, Supco SS-410. They are made for high torque 1/3 hp compressors, always keep a couple with me for in a pinch. That being said, I almost always return to install proper start components (...
  7. Replies
    91
    Views
    8,312

    Time for a Term-Lok kit:grin2:

    Time for a Term-Lok kit:grin2:
  8. If you do some poking around here, Rockit spelled...

    If you do some poking around here, Rockit spelled it out perfectly a few years ago, and should help you out quite a bit...

    Hope this helps...
  9. Non- condensables :oops: Ya didn't pull a...

    Non- condensables :oops:

    Ya didn't pull a vacuum did ya....
  10. Replies
    27
    Views
    2,208

    Also if return ducting is flex , check for...

    Also if return ducting is flex , check for dampers , may be closed or not open all the way :.02:

    Hope this helps
  11. Replies
    41
    Views
    4,349

    Check out the link on post #2 Hope this helps...

    Check out the link on post #2

    Hope this helps

    Or
    Also as Mike19 posted. Sporlan 90-30-1
  12. Replies
    41
    Views
    4,349

    Anytime:cheers:

    Anytime:cheers:
  13. Replies
    41
    Views
    4,349

    Yes, same thing as the link from my first first...

    Yes, same thing as the link from my first first or second post.
  14. Replies
    41
    Views
    4,349

    You should be fine with that receiver , will be...

    You should be fine with that receiver , will be cutting it close by the numbers.

    Hope this helps
  15. Replies
    41
    Views
    4,349

    You may not, but now we can figure it out, now...

    You may not, but now we can figure it out, now that we have the condenser model number. Ya didn't give me much to go on before.

    Will check on it for ya.
  16. Replies
    41
    Views
    4,349

    You will need a larger receiver.... ...

    You will need a larger receiver....

    http://www.industrialcontrolsonline.com/training/online/refrigeration-pressure-regulators-flow-controls-parts-1-and-2

    There is a formula a little way down (...
  17. Way to work yourself out of getting help:whistle:...

    Way to work yourself out of getting help:whistle:
    And 35 years of commercial experience and you can't wire the most basic control circuit. Hahaha. :beat::beat:
  18. Replies
    20
    Views
    1,919

    Have you checked the water inlet valve ... I had...

    Have you checked the water inlet valve ...
    I had one intermittently bleed by and it actually wouldn't start until about 15 mins after calling for water.

    Just a thought
  19. Thread: moisture?

    by skpkey9
    Replies
    15
    Views
    2,186

    That poor poor machine. :pop:

    That poor poor machine. :pop:
  20. Replies
    22
    Views
    3,132

    X 2

    X 2
  21. Replies
    19
    Views
    3,608

    I've seen 250 and I'll bet anything people around...

    I've seen 250 and I'll bet anything people around here have seen higher. And for me 50 degrees is a little to close for comfort. Tho it's rare it does and can happen. And it could very well fail...
  22. Replies
    19
    Views
    3,608

    Temp range is to 300, I wouldn't use it on a...

    Temp range is to 300, I wouldn't use it on a discharge line. :.02:

    Just sayin
  23. Replies
    79
    Views
    13,967

    It's a kit. Build a valve. He won't find...

    It's a kit. Build a valve. He won't find anything he can use on that body.
    He'd need to pull the head and check the valve for sizing. Unless someone put the tag on.

    Hope this helps
  24. Replies
    29
    Views
    6,544

    :oops: oops. For some odd reason I had pictured...

    :oops: oops. For some odd reason I had pictured walk in when I answered. Hate it when that happens. LOL :bsing:
  25. Replies
    79
    Views
    13,967

    I'd say you hit the nail on the head... That...

    I'd say you hit the nail on the head...

    That valve is most likely undersized. :det:
  26. Replies
    29
    Views
    6,544

    Replace drier , when unit is close to temp check...

    Replace drier , when unit is close to temp check SH and adjust accordingly, for compressor protection.

    And most important. Tell them to stop using it like a reach in. It's not designed for that....
  27. Replies
    23
    Views
    3,215

    And the $ 100,000 question.... Where is the...

    And the $ 100,000 question....

    Where is the leak ?:.02:
  28. Replies
    13
    Views
    2,831

    I'm trying to help you, but you keep failing to...

    I'm trying to help you, but you keep failing to read what I'm typing. And stating the same thing back to me that I'm telling you.

    This is the second post you did this. We are here to help you,...
  29. Replies
    13
    Views
    2,831

    You say when harvest did work your suction...

    You say when harvest did work your suction pressure was 80-90.
    In your earlier post you said harvest suction pressure was 45 psi
    cool vapor valve is hanging up intermittently on ya as well.
    ...
  30. Replies
    13
    Views
    2,831

    Cool vapor valve is what I called it in my post. ...

    Cool vapor valve is what I called it in my post.
    Cool vapor valve is piped into the top of the receiver and uses the gas that accumulated at the top of the receiver for harvest.
    As where a hot...
  31. Replies
    13
    Views
    2,831

    Suction pressure way too low for harvest. Will...

    Suction pressure way too low for harvest. Will not generate enough heat to shed the ice off the plate. Are you sure it's not a cool vapor valve that you are calling a hot gas valve. If so it will...
  32. Replies
    37
    Views
    4,521

    That's what I said in previous post. LoL:cheers:...

    That's what I said in previous post. LoL:cheers:

    Besides what residential out there even comes close to holding 50lbs :grin2:
  33. Replies
    37
    Views
    4,521

    Find a new company. The site of the leak should...

    Find a new company.
    The site of the leak should be located.
    How old is the system in question?
    A leak the large should be able to be found in 5 minutes with some nitrogen if the system is flat (...
  34. Replies
    37
    Views
    4,521

    You are 100% correct. Only systems exceeding...

    You are 100% correct.
    Only systems exceeding 50lbs
  35. Replies
    37
    Views
    4,521

    That EPA limit is only schedualed for commercial...

    That EPA limit is only schedualed for commercial systems exceeding 50lbs od refrigerant.

    Hope this helps

    To the OP
    The guy is just trying to make a sale if he is not giving you any options.
  36. Replies
    17
    Views
    2,600

    Bonnie , just checking to see if you found my...

    Bonnie , just checking to see if you found my email address.
  37. Replies
    17
    Views
    2,600

    If you'd like a second opinion you can find my...

    If you'd like a second opinion you can find my email in my profile, contact me and we can set up a time to see what you have going on with your system. I'm not too far away from you.
  38. Replies
    17
    Views
    2,600

    Your system is not oversized unless your home is...

    Your system is not oversized unless your home is super insulated...

    Thats just going off the information that was given to us.
  39. Replies
    17
    Views
    2,813

    http://www2.schneider-electric.com/resources/sites...

    http://www2.schneider-electric.com/resources/sites/SCHNEIDER_ELECTRIC/content/live/FAQS/130000/FA130583/en_US/Corner-Grounded%20Delta%202700DB0202.pdf


    Hope this helps
  40. Replies
    63
    Views
    8,193

    It's a shame they did that to ya... Hope this...

    It's a shame they did that to ya...

    Hope this is what you are looking for.


    http://www.mbm-service.de/mbmTechTwo/True_/GDM-5+/Service_Manual.pdf
  41. Your problem is not the size of the unit, it's in...

    Your problem is not the size of the unit, it's in your set up .

    The unit is sized properly , at a mid point average load you are looking at 50 btuh per square foot @ 7000 sq ft gives you 29.16...
  42. Replies
    91
    Views
    28,860

    Looking for qualifier in pinellas, hillsborough...

    Looking for qualifier in pinellas, hillsborough area to qualify company. Thanks
  43. Replies
    13
    Views
    1,827

    There are several variables Is the unit...

    There are several variables
    Is the unit residential or commercial
    Also from brand to brand ESP will vary.
    Need more information to be able to help you but I can tell you that the numbers you...
  44. That is the wrong compressor for what he's trying...

    That is the wrong compressor for what he's trying to accomplish...
    Not enough capacity.

    Hope this helps
  45. I suggest you call a new company or ask for a...

    I suggest you call a new company or ask for a senior tech to diagnose and if that was the senior tech , back to call out a new company.

    Sorry
  46. Thread: In need of

    by skpkey9
    Replies
    9
    Views
    989

    First Co. Also makes them. Hope this helps

    First Co. Also makes them.

    Hope this helps
  47. Replies
    33
    Views
    3,238

    JP- I have it someplace , will look for it in a...

    JP- I have it someplace , will look for it in a bit and get it over to you ..
  48. Replies
    21
    Views
    2,191

    Yes, But with 438 (MO99) there is a huge loss in...

    Yes, But with 438 (MO99) there is a huge loss in capacity... He need to let this one go.:.02:
    No good deed goes unpunished.:pop:

    Hope this helps...
  49. Replies
    21
    Views
    2,191

    Run Forest Run !!!:grin2:

    Run Forest Run !!!:grin2:
  50. Replies
    9
    Views
    1,473

    In cooling the evap check valve is closed, and...

    In cooling the evap check valve is closed, and yes there is a screen.
    It's possible ball is not seating properly causing frosting. For temporary repair, crimp check valve body with pinch off tool...
Results 1 to 50 of 846
Page 1 of 17 1 2 3 4

Related Forums

Plumbing Talks | Contractor MagazineThe place where Electrical professionals meet.
Comfortech 365