Search:

Type: Posts; User: bku46

Page 1 of 7 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    12
    Views
    2,131

    Buy a new pan

    Buy a new pan
  2. Replies
    18
    Views
    1,924

    Get yourself a good hammer

    Get yourself a good hammer
  3. Replies
    10
    Views
    4,243

    Do yourself a favor, get Rover:]

    Do yourself a favor, get Rover:]
  4. Thread: trane rtac

    by bku46
    Replies
    14
    Views
    2,526

    Oil over charge will not cause his problem, had...

    Oil over charge will not cause his problem, had several units with oil over charge, unit trips on low refrig level, also tev goes open 100% and flashing in the sight glass. Been there and done that.
  5. Thread: trane rtac

    by bku46
    Replies
    14
    Views
    2,526

    There are no filters on a RTAC, only oil filter...

    There are no filters on a RTAC, only oil filter on compressor. Set your low refrig cutout to 28.0 That is the proper setpt for water. Make sure the chiller is controlling the pump, if pump not...
  6. Thread: trane rtac

    by bku46
    Replies
    14
    Views
    2,526

    Your approach temp should be 5 check your...

    Your approach temp should be 5 check your condenser superheat, should be around 15 degrees, is the sight glass flashing? What is the evap sat temp? what is your suction press.?
  7. Thread: trane rtac

    by bku46
    Replies
    14
    Views
    2,526

    Is this a water or glycol system? What is your...

    Is this a water or glycol system? What is your leaving water stpt? What is your approach temp? what is your superheat? What is the current avg % at start? There are many factors to look at to resolve...
  8. Replies
    8
    Views
    942

    You must get the Trane sensor, do it right...

    You must get the Trane sensor, do it right please, dont basterize another Trane unit.
  9. Replies
    24
    Views
    2,107

    JTRICOR Can you spell Varitrac? daaa I know you...

    JTRICOR
    Can you spell Varitrac? daaa I know you can use old hyper term, but the guy has no laptop, daaaa maybe you can send him yours.
  10. Replies
    19
    Views
    2,948

    Before you go off on a tangent, First did you put...

    Before you go off on a tangent, First did you put gauges on the unit? monitor the compressor amps at start and after? Do the common sense things so you can see what is causing the trips, Check you...
  11. Replies
    24
    Views
    2,107

    Well, it would be great if you had the Tracker...

    Well, it would be great if you had the Tracker software and a laptop, but you can go thru the menues. I would first run the unit thru test mode in make sure everything stages on. Then I would review...
  12. Replies
    38
    Views
    3,138

    Whatever, Thats why I make the big bucks and you...

    Whatever, Thats why I make the big bucks and you dont.
  13. Replies
    38
    Views
    3,138

    I gave you the conventional stat wire...

    I gave you the conventional stat wire terminations jack ass I realize that. I could give you the proper terminations for the Baysensor but your a ahole and you can figure it out yourself.
  14. Replies
    4
    Views
    1,182

    you should see all active and history diagnostics...

    you should see all active and history diagnostics from the display, unless its a auto reset diagnostic like flow loss.
  15. Replies
    38
    Views
    3,138

    Let me tell you want a be mechanics something, I...

    Let me tell you want a be mechanics something, I do know my **** and thats why I make 38.00 per hr. I installed many of these Trane stats with no problem, In fact I work for Trane. I get you guys all...
  16. Replies
    38
    Views
    3,138

    I hope the customer isnt getting billed for your...

    I hope the customer isnt getting billed for your in experience. What would you do if you had a real problem, Maybe you should just call a Trane tech next time.
  17. Replies
    38
    Views
    3,138

    Like I said, if you read the info that comes with...

    Like I said, if you read the info that comes with the stat and follow the directions I think any ass can figure it out but some guys cant read.
  18. Replies
    38
    Views
    3,138

    OK, Listen and listen good, write it down. First...

    OK, Listen and listen good, write it down. First run the unit thru test mode, that will rule out any problem with the UCP, ok now if that checks out, then here are your LTB1 connections as follows:...
  19. Thread: What's this POS?

    by bku46
    Replies
    7
    Views
    1,087

    Jackson Church

    Jackson Church
  20. Replies
    38
    Views
    3,138

    ultatech, I do nkow it all.

    ultatech, I do nkow it all.
  21. Replies
    7
    Views
    1,308

    There are restricters inside the cap tubes where...

    There are restricters inside the cap tubes where it enters the evap, if you look close you can see them, Try heating that spot with a tourch and hope for the best.
  22. Replies
    38
    Views
    3,138

    Maybe you should read the paper that came with...

    Maybe you should read the paper that came with the tstat or did you wipe your ass with it.
  23. Replies
    20
    Views
    1,816

    Dale, go get some training on a thing called...

    Dale, go get some training on a thing called super heat and sub cooling, maybe your problem will go away.
  24. Replies
    7
    Views
    1,319

    Try trouble shooting the unit. Isolate the...

    Try trouble shooting the unit. Isolate the problem and fix it. Sometimes you really have to think in this bussiness.
  25. Replies
    7
    Views
    1,308

    Do yourself a favor, replace the evap coil, had...

    Do yourself a favor, replace the evap coil, had problems with restricted cap tubes, tried heating them up to melt waxing but to no avail, replaced the evap and running like new.
Results 1 to 25 of 169
Page 1 of 7 1 2 3 4
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event