Search:

amana is piss of sh.t!!!="GOODMAN"
GET TRANE! OR CARRIER

Only By Subcooling If Is Txv Sys At Least 60 F Ambiant!!!!!

whats you liquid line temp and hih side presure? ask the guy to change only the back part of the motor the electronics!

you will have lots of problem with static pressure if you are using infinity zone contols by looking those zones.....you had to oversize all zones each zone to be capable 75% by it self read zonning...

carrier only makes 2,3,4 and 5 ton cond units in infinity as you contractor to check sys pressures and make sure he checks it by subcooling ask him to tell you what subcooling is running i think 5...

infinity looks at out door unit and determs the cfm by it u can not adj CFM on infinity to reset it you have to go to addvance

1.Your sys should be service every year by pro
2.Not blowing cold enough could be low on freon
2.Not blowing as use to could be dirty filter or freezing coil do to low on freon
3.Use white...

may be you should start to charge 410A by gas since is so close.....wasnt supply house was in puron class by carrier.....

did you check if is windings are gorunded??? also owm out winding.....and try to add hard star kit..........my ex boss (plumber) told one time to hit the compresor with 2x4 and hamer on top of of...

BECOMES HIGHLY FLAMEBLE!!!!not a good idea :) PUT new 410a if you have leak!!!!!!!!!!!

you miss understood the point i was thiking since the txv froze been coolder than the bulb which is on suction bulb charge magrate to powerhead....not the freon!!!!!

but the fact sys worked last summer.......and i checked the vents and return i the house ok....

it was freezing up still right after txv......when i was trying to add more 410a (after 4F subcooling ) freezing moved down where dist tubes wore anterying the coil......and then when i was done...

custumer said that has been freezing up for the past month and he was shuting off to unmelt and then he was putting back on also the previose service tech when he did start and test on the new sys...

low

after 3lbs of 410a sys ran with 4F of subcooling and low side was around 70 psi and high side around 250 psi but sence txv was not oppening not acts like fixed orfice so i didnt want to leave the...

was joking....

......remove sencing bulb warm up by hand low said still the same

about 1 year old sys worked 1 summer this is the 2 summer....found sys low 0F subcooling (side glass bubles):D added 3 lbs of 410 A (service tech left caps off service valve) sys runs now with 4F of...

:confused:I bought my digital gauges about 1 year and 4 mon....(http://www.jbind.com/catalog_multi-page/Page_10-11_JB_Industries_2007_catalog.pdf) JB i had them change twice first year under warranty...

http://www.geocities.com/nikola36/000_0076.jpg


http://www.geocities.com/nikola36/000_0078.jpg


http://www.geocities.com/nikola36/000_0077.jpg

You duct is small or u dont have enough run ON THAT ZONE, that zone only will open if other zone calls for heat/cool

Infinity Zoning System!!!!!!!!

clean ur flame sensor with sandpaper or check the hose of the presure switches

YES u can add hydro coil and u can wireto the A/H u need to cut 2 wires and use DC relay and u need to set up 5,8,9,10,20 KW (AIRFLOW) ON THE infinity control the only problem is when control calls...

http://www.youtube.com/watch?v=8IQfpkh1Y_M

HOLD TOP LEFT AND TOP RIGHT (FAN) FOR FEW SEC :)))) HAVE FUN!

i had 3 sys carrier infinity where was not charge correcly and the coils freez up!