Search:

Type: Posts; User: CB_Matt

Page 1 of 5 1 2 3 4

Search: Search took 0.00 seconds.

  1. Thread: KMC Trainer

    by CB_Matt
    Replies
    2
    Views
    335

    That is a 5831 and a 5801. Its possible that the...

    That is a 5831 and a 5801. Its possible that the variables were never named. I will hunt around and see what i can find.
  2. Replies
    4
    Views
    339

    The points live in the individual Tux-Vav...

    The points live in the individual Tux-Vav controllers and will come through.

    I have a manual that will give you all that you need. You will have to add you email to your profile so that i can...
  3. Replies
    4
    Views
    339

    All of the items that you list are no longer...

    All of the items that you list are no longer made, but you can intrface and get the data out of them but you will need a BCM-Pwr, BCM-Eth, and BCM-Tux.
  4. Replies
    5
    Views
    386

    There is a zero cutoff and a calibration factor....

    There is a zero cutoff and a calibration factor. I dont have the info in front of me right now, but will see if i can find these points for you.
  5. Replies
    5
    Views
    386

    I dont know why you would need a Spyder license...

    I dont know why you would need a Spyder license for an Alerton controller, but you can get into balance mode on the microset ( If Installed). Otherwise there are only a couple points that you need to...
  6. Replies
    15
    Views
    891

    Sure thing!

    Sure thing!
  7. Replies
    15
    Views
    891

    You can pulse the inputs, but you do not have to....

    You can pulse the inputs, but you do not have to. It also works if the inputs come on and stay on. Reset input has the highest priority and will override the set input.

    Simulate by turning on the...
  8. Replies
    15
    Views
    891

    Sorry I thought that would come through. This one...

    Sorry I thought that would come through. This one is done with two or blocks. Not the outputs of the two blocks. Set is the top input and reset is the bottom. I will try to clean up the image and...
  9. Replies
    15
    Views
    891

    Flip Flop

    http://hvac-talk.com/vbb/attachment.php?attachmentid=450781&d=1388666649


    THis is a good way to build a flip flop also
  10. Replies
    15
    Views
    891

    Do you have an XOR block ( exclusive or ) Link...

    Do you have an XOR block ( exclusive or ) Link the out of the xor back into an input. This will substitute for the last value block.
  11. Replies
    4
    Views
    432

    I have done alot of work on ALerton systems in...

    I have done alot of work on ALerton systems in Iowa in the past. If you email me i should be able to help you out.
  12. Replies
    9
    Views
    702

    This is good to know. I had originally though...

    This is good to know. I had originally though that any Jace could be licensed to add Spyder and have the ability to program. I did not know that Honeywell's position is that you have to spend x...
  13. MazdaJoe, Could you tell me who you stated that...

    MazdaJoe, Could you tell me who you stated that you are not supposed to use the rate limit block? I would agree with this statement because you should be able to slow the pid to accomplish the same...
  14. I would also try getting rid of the deadband...

    I would also try getting rid of the deadband completely. Let the PID always have control of the firing rate.
  15. Replies
    20
    Views
    2,514

    http://hvac-talk.com/vbb/attachment.php?attachment...

    http://hvac-talk.com/vbb/attachment.php?attachmentid=440691&thumb=1&d=1342711228


    Take a look at this photo and you will realize that the Spyder Learning Curve is way to long to discuss the...
  16. Replies
    175
    Views
    24,170

    Reckles, Is this installed on a VM?

    Reckles,

    Is this installed on a VM?
  17. Replies
    37
    Views
    2,118

    Deepest sympathies go out to you and your family.

    Deepest sympathies go out to you and your family.
  18. Replies
    3
    Views
    1,034

    Proper Jace Install

    432761

    This is the proper way to install a Jace, I guess?
  19. Replies
    9
    Views
    697

    One other thing to look at is this. In the Venom...

    One other thing to look at is this. In the Venom apps, if you look you will see that they use a cycler and stager, set them up the same and take the lower of the two. I can't remember but i think one...
  20. Thread: Controls Tech

    by CB_Matt
    Replies
    3
    Views
    554

    Programmers

    Chuck,

    Get in touch with me. I think that i can help you out. My email address is in my profile

    Matt
  21. I would say sell it, but as soon as you do there...

    I would say sell it, but as soon as you do there will be a new Spyder tool and then you fix will probably be no good. :(
  22. I had this issue once. It was a Mcquay chiller...

    I had this issue once. It was a Mcquay chiller with a Lon controller though. The issue that i discovered was the electricians when installing my 1" conduit to the chiller for the Lon bus, laid it in...
  23. Replies
    37
    Views
    1,983

    When i bring controllers in across multiple...

    When i bring controllers in across multiple MS/TP's into the same system i use a numbering scheme that adds the network number to the mac address. Mac 1 on Network 2000 = 2001, Mac 1 on Network 2100...
  24. Replies
    37
    Views
    1,983

    Also 127 is an addressing limitation. I am sure...

    Also 127 is an addressing limitation. I am sure if the unit loads are calculated that trunk would be overloaded.

    Most of the manufacturers that i work with say 65 controllers per comm line.
  25. Replies
    18
    Views
    1,952

    BAM! Old school Subroutines. I used to love these...

    BAM! Old school Subroutines. I used to love these for controlling multiple controllers.

    Yep forgot to mention that they may have this buried in a Subroutine.
Results 1 to 25 of 111
Page 1 of 5 1 2 3 4
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event