Search:

Type: Posts; User: Brad gall

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Blade hasnt slide down the shaft and not running...

    Blade hasnt slide down the shaft and not running backwards.
    piston also correct
    Amana tech wants me to change the blade and motor because he said it should be drawing closer to 1 amp and its...
  2. 26 degree but also air seems to be coming out...

    26 degree but also air seems to be coming out the top 5inches of the condenser coils and out the top
  3. possible ive either seen them good or bad I was...

    possible ive either seen them good or bad I was thinking maybe the blade got bent but it dosent seem to be??
  4. 35/5/440 dual cap

    35/5/440 dual cap
  5. dual cap 35/5/440

    dual cap 35/5/440
  6. going over when I get a motor an blade just i...

    going over when I get a motor an blade just i ncase. It seems the condenseris not rejecting the heat an the condeser is clean for the amp draw to be that low???
  7. ran fine 8 years, pumped down with micron guage....

    ran fine 8 years, pumped down with micron guage. matched amana 2.5 ton
  8. should the amp draw be half of the rla on one leg...

    should the amp draw be half of the rla on one leg I think the rla was 1.2 & .6 on one wire
  9. never been replaced but im wondering if the...

    never been replaced but im wondering if the homeowner bent the blade cleaning out the unit
  10. rotation correct . I was thinking probably...

    rotation correct . I was thinking probably running hot with those pressures popped the capacitor to start with.
  11. would it make the pressures fluctuate if the fan...

    would it make the pressures fluctuate if the fan blade was bent . because the homeowner vacumed out the leaves he said and I was thinking maybe its not rejecting the heat but I dont know if that...
  12. 64oz and the lineset was @20ft

    64oz and the lineset was @20ft
  13. new 22 I charged by weight and pressure the same...

    new 22 I charged by weight and pressure the same as the first day I was there 85suc 350liq both fluctuating @70/85 315/350
  14. ive already put new 22 in but my pressures...

    ive already put new 22 in but my pressures continue to fluctuate like theres non condesables. not sur what else would cause this
  15. changed filter drier and weigh charge in still...

    changed filter drier and weigh charge in still same problem any ideas?
  16. ga1279 Im going to change the drier out and yes...

    ga1279 Im going to change the drier out and yes my pressures were moving around alot which intern was changing my temp. reading as they moved around so did my temps

    Thanks alot i really...
  17. Im going to and already should have Thanks so...

    Im going to and already should have Thanks so much ill let you know how it goes
  18. I just checked the tempature across not sure...

    I just checked the tempature across not sure aboout the psi unless you have a port there to check it
  19. when i got there i didnt add any refrigerant It...

    when i got there i didnt add any refrigerant It was running at 85/350 then i cleaned condenser and no difference. Although both pressures and line temps were fluctuating.
    My superheat and subcooling...
  20. Anyone know a list of things that would cause the...

    Anyone know a list of things that would cause the fluctuating of pressures and temps
    I thought non condesables,air, moisture
    condenser recirculation?
    condenser fan not functioning 100% (how to...
  21. What about the pressures fluctuating? the...

    What about the pressures fluctuating?
    the pressures both are going up and down along with my line temps ?
  22. a/c problem everythings running but need help

    Call started off a bad compacitor then i noticed they hadnt changed there spacegaurd for a while. Got unit up and runnning and told them to leave off till i got filter next day. Replaced filter unit...
  23. New install I just had one i couldnt get any SH,...

    New install I just had one i couldnt get any SH, subcooling was within range. I really didnt want to change the txv so i tried the charge/airflow/ and my txv would even throttle refrigerant when i...
  24. Replies
    11
    Views
    897

    Ok thanks, Is there any ways for me to obtain pro...

    Ok thanks, Is there any ways for me to obtain pro status or do i have to post alot of threads?
  25. Sticky: how i got into hvac

    Well my whole life i loved working on things and was always good with tools.
    Ive always been a hard worker and had a job since i was 12 yo. Well needless to say i never made a whole lot of money...
Results 1 to 25 of 57
Page 1 of 3 1 2 3
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event