Search:

Type: Posts; User: kslrr

Search: Search took 0.00 seconds.

  1. Replies
    3
    Views
    861

    Hey thanks aec_control_tech for the replies. I...

    Hey thanks aec_control_tech for the replies. I actually contacted Echelon with the question and they described the Z index and a fellow I know told me that the Front/Back buttons do not always work....
  2. Replies
    31
    Views
    2,082

    You need an active 0-10 volt sensor. Terminating...

    You need an active 0-10 volt sensor. Terminating a thermister (NTC, PTC. 1k, 10k, etc.) will not work. A 0-10 analog input does not have the dc excitation voltage present. A 3 wire or 4 wire 0-10...
  3. Replies
    2
    Views
    2,067

    It's been years since I've setup a DD VAV, have...

    It's been years since I've setup a DD VAV, have always delt with flow sensors in the HD and CD, but you indicate that the controller is setup for Discharge Sensor. Did you check the K factor? If it...
  4. View Post

    <ok since I can't figure out how to edit my own post, I will continue here>

    I worked for JCI 3 years and was layed off twice: once in CA, once in NV. I saved the engineering dept in Las Vegas; A...
  5. I have worked for both Siemens and JCI as a...

    I have worked for both Siemens and JCI as a Systems/Design Engineer. After 13 years at Siemens (Staefa, Landis & Staefa, Siemens) I knew the legacy products, the new products and pneumatics as well....
  6. Replies
    3
    Views
    861

    Echelon iLON Vision graphics

    When inserting layers and then Images within these layers, the Front to Back order seems to be random and the "Bring to front" and "Send to Back" buttons do not work. How do you adjust the Front to...
  7. Replies
    36
    Views
    5,983

    The passkey is "BTCVT".

    The passkey is "BTCVT".
  8. Replies
    36
    Views
    5,983

    No he means the PC software. Even though I...

    No he means the PC software. Even though I followed the instructions very closely, so I thought, I was getting errors until I called our regional guru and he pointed out which "i"'s I did not dot...
  9. Replies
    36
    Views
    5,983

    I have not attempted Ethernet Passthru because we...

    I have not attempted Ethernet Passthru because we are encouraged to use the BTCVT which sets up a Bluthtooth connection on the FC or SA buses, both of which are BACnet MS/TP, to connect to the Field...
  10. Replies
    36
    Views
    5,983

    Hmmm... Interesting. The reason I asked is...

    Hmmm... Interesting. The reason I asked is because I work for JCI and as far as I know the new product can only be purchased as part of a complete system design and installation. The MSEA (MetaSys...
  11. Replies
    36
    Views
    5,983

    How is it that you have obtained a JCI NCE? Are...

    How is it that you have obtained a JCI NCE? Are you a JCI employee? If so, why are you asking here for help? Are you a previous JCI customer?
  12. Replies
    38
    Views
    2,359

    How about the guy who played with Huey Lewis? ...

    How about the guy who played with Huey Lewis?

    Other names I have not seen: Phill Keagy, Mark Nopfler and Brian Sestzer (not sure of spelling of last names).

    Also there was this little guy who...
  13. Replies
    1
    Views
    2,478

    ESUSA NexSys, Siemens & Carrier for sale

    Part # Desc. Qty.

    NexSys Items

    NXP-FSC-01 Flexible System Controller 4
    8UI 8 Universal Input board ...
  14. Replies
    66
    Views
    3,645

    I ride bikes. I have an '04 Harley Sportster 883...

    I ride bikes. I have an '04 Harley Sportster 883 Custom, a '72 Honda CB350F, an '81 Honda CB640 Custom, a '77 Yamaha XS750 tripple and now an '81 Yamaha IT465. I am also into music (guitar),...
  15. Replies
    14
    Views
    2,010

    Could you use these?

    I have a rebuilt MST-01E and 2 MST-01ES's that have been in my garage since the mid '90's. Would the 01E work for you?
  16. Thread: Noobie here

    by kslrr
    Replies
    1
    Views
    439

    Noobie here

    Well, new to this forum (just found it while doing a search on ECM motors) but not to HVAC. I have worked in the controls industry since 1986 (Honeywell, York, Carrier, Robinsons/May, Staefa, Landis...
Results 1 to 16 of 19
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event