Search:

Type: Posts; User: GastecD

Page 1 of 2 1 2

Search: Search took 0.01 seconds.

  1. Replies
    11
    Views
    821

    It's up and running! Made some adjustment on...

    It's up and running! Made some adjustment on incoming water
  2. Replies
    11
    Views
    821

    Its a new unit, and you would be right to assume...

    Its a new unit, and you would be right to assume it is a water cooled condenser- by municipal water, Incoming water temperature is 42 degrees. Outlet is no more than 50.

    I'm not adjusting the high...
  3. Replies
    11
    Views
    821

    the high pressure cut off set point is 400 psi,...

    the high pressure cut off set point is 400 psi, the unit is controlled by a pressure differential switch
  4. Replies
    3
    Views
    903

    And so it was

    And so it was
  5. Replies
    11
    Views
    821

    New install, problem at start up.

    I dont do very much refrigeration, A friend of mine asked me to install a walk in box for his cottage to hang game in

    We put the box up and Installed all the equipment as per the engineers sizing...
  6. Replies
    3
    Views
    903

    Keeprite furnace diagnosis

    No heat call for a Keeprite furnace
    Honeywell sv9541

    Call for heat
    pressure switch proven
    hsi energized
    pilot gas ignited
    hsi de-energized
    pilot valve remains on- no main burner
    indoor...
  7. Replies
    5
    Views
    1,241

    Carrier 40aq air handler electric heat

    No heat call, found the filter was plugged solid and coil.

    With the blower door off Im bypassing the coil and the unit works.

    I would assume that with the door on and the unit calling for heat...
  8. Replies
    37
    Views
    3,367

    Have you tried removing one that was siezed?

    Have you tried removing one that was siezed?
  9. Replies
    23
    Views
    2,615

    I can't believe this... A condo full of these? I...

    I can't believe this... A condo full of these? I think a license should be revoked
  10. Replies
    37
    Views
    3,367

    Agree with changing the furnace, once you have to...

    Agree with changing the furnace, once you have to change out a spark plug youll be wishing you had
  11. Replies
    7
    Views
    906

    This could come in handy, thanks. Also did...

    This could come in handy, thanks.

    Also did some researching, thinking an instant hot water heater with a recirc pump on it, may do the trick. Looks like the gpm they require will match up with...
  12. Replies
    21
    Views
    2,355

    The sewer smell is throwing me off, is it...

    The sewer smell is throwing me off, is it possible something is on the heat strip thats burning, is the duct lined with anything? ie acoustic insulation?
  13. Replies
    13
    Views
    1,413

    That is strange, make sure to share the outcome....

    That is strange, make sure to share the outcome. Never know when youll come across something like this
  14. Replies
    7
    Views
    906

    Hydronic question

    A commercial bakery I do some work for asked me if there was a way to get 86 degree water for dough mixing.

    They would require approx 40 L of water every 10 minutes for each mix.

    Tankless...
  15. Replies
    2
    Views
    478

    The economizer are off and fresh air dampers set...

    The economizer are off and fresh air dampers set for 25% fresh air as per building code. Supply air temp was 68 on start up, 73 after running for a few minutes.

    The unit is horizontal discharged,...
  16. Replies
    23
    Views
    2,274

    We do the same, its a liability - being the last...

    We do the same, its a liability - being the last licensed technician to service the appliance it becomes our responsibility to ensure its running safely.
  17. Replies
    2
    Views
    478

    York 20 rtu blower delay adjustment

    Got a call with complaints of cold air coming out of the supply runs during the start of the heat call making patrons uncomfortable.

    Looking to adjust the blower on delay so the air isnt as cold...
  18. Flame roll out, change the board. Imagine if all...

    Flame roll out, change the board. Imagine if all mechanics did the same!
  19. Replies
    26
    Views
    2,596

    Depends how hard its raining and from what...

    Depends how hard its raining and from what direction. Ive serviced RTUs in the rain by putting the panels on top with a patio slab from the roof to stay dry.
  20. Replies
    11
    Views
    1,764

    Are you referring to the limit switch?

    Are you referring to the limit switch?
  21. Replies
    57
    Views
    4,147

    You could have a crack in the porcelain around...

    You could have a crack in the porcelain around the flame sensor that once heated expands and grounds out
  22. Replies
    6
    Views
    762

    that would be great! I just got back from...

    that would be great! I just got back from Nashville Tennessee with Goodman Manufacturing speaking to some of the west coast guys. G3 fitter- restricted to furnace cleanings alone and under the...
  23. Sticky: winter rolling in now doing heat start up and...

    winter rolling in now doing heat start up and inspections.. working on a funeral home today doing a start up before the place opens ( trying to get all the kinks out so we dont have to return when...
  24. Sticky: Hello from Ontario, Ive been part of the hvac...

    Hello from Ontario,

    Ive been part of the hvac trade since my conception lol.. my mom would drive around pregnant with my dad who is self employed on some late night service calls to keep him...
  25. Replies
    6
    Views
    762

    New to site from Ontario

    Hello. Been in the trade for 6 years now licensed g1 fitter and refrig mech
Results 1 to 25 of 35
Page 1 of 2 1 2
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event