Search:

Type: Posts; User: Ctl-fool

Page 1 of 7 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    26
    Views
    6,768

    Has there been any success in adding 3rd party...

    Has there been any success in adding 3rd party bacnet mstp or ip devices (Ie a multistack chiller with bacnet mstp or aaon rooftop with lynxspring bacnetip) onto a tracer sc? according to the...
  2. Replies
    26
    Views
    6,768

    So, if you added a bacnet 3rd party mstp device...

    So, if you added a bacnet 3rd party mstp device onto the network, you could add it to the network and populate the points with the sc ui?
  3. Replies
    26
    Views
    6,768

    Anybody using SC yet? How does it compare to Ax...

    Anybody using SC yet? How does it compare to Ax - does it have an equivalent to workbench or do you need Trane software to engineer it?
  4. Replies
    14
    Views
    1,397

    Any idea if the Staefa Talon is open?

    Any idea if the Staefa Talon is open?
  5. Replies
    8
    Views
    1,356

    Any chance someone could send me the...

    Any chance someone could send me the lonHoneywellAxWizards jar file to? :putergreet:
  6. Replies
    16
    Views
    1,592

    If soneone could send me the jar file, I'd...

    If soneone could send me the jar file, I'd appreciate it. :putergreet:
  7. Replies
    59
    Views
    6,653

    any chance I could get those reference manuals? ...

    any chance I could get those reference manuals? Need some more late-night reading material. :eek2:
  8. You should have a VAV calibrate schedule that I...

    You should have a VAV calibrate schedule that I believe opens and closes the air valve and water valve during this recalibration.
    I'm pretty sure the calibration drives both valves closed and then...
  9. Trane Tracer Summit VAV II/III UCM Reheat Valve Water Flush

    Does anyone know of an easy way to globally force Trane VAV UCMs on a summit network to drive all the reheat valves open? I know there is a check box setting on one of the UCM tab pages in UCM...
  10. Replies
    13
    Views
    2,276

    Any chance I could get the apogee insight users...

    Any chance I could get the apogee insight users manual? email is in profile.

    would greatly appreciate it.:angel:
  11. Replies
    13
    Views
    1,741

    any 0-10v inputs on this controller? Heard of...

    any 0-10v inputs on this controller? Heard of ahu controllers resetting if the input goes over the 10vdc limit.
  12. Replies
    22
    Views
    2,569

    Anyone seen anything new on this? Hardware...

    Anyone seen anything new on this? Hardware components/IT requirements/interfaces for 3rd parties?

    :bump:
  13. Replies
    13
    Views
    2,025

    Just wire +/- to +/-. I think Ive done that for...

    Just wire +/- to +/-. I think Ive done that for an FX60 once and it worked.:putergreet:
  14. Replies
    5
    Views
    1,132

    Interesting....id suspect that there has to be...

    Interesting....id suspect that there has to be some software separation that differentiates webctrl from i-vu. I cant imagine that they would allow for ALC ifos/branches and Ivu dealers to go...
  15. Replies
    5
    Views
    1,132

    WebCtrl Vs I-vu?

    Anyone familiar enough with both to say what the main differences are? I-vu speaks CCN for the legacy controllers, and Bacnet with the Open controllers, the pretty much look like the ALC stuff...
  16. Replies
    0
    Views
    419

    Older ALC CMnet Portal

    Am looking for an older piece of ALC equipment to do CMnet to Bacnet, the Portal module which used the older exec 4 or exec 6 firmware.

    Anyone have one of these lying around?
  17. too bad....RZ had an interesting product, with...

    too bad....RZ had an interesting product, with alot of 3rd party drivers for legacy integration.
  18. So, this is the death of Richards-zeta/cisco, or...

    So, this is the death of Richards-zeta/cisco, or will RZ be spun back off into a seperate company?
  19. Replies
    4
    Views
    493

    Yup, I know we could keep the bmtw to use as a...

    Yup, I know we could keep the bmtw to use as a gateway, just looking at options should we want to take the bcu out. currently the bcu has 1 comm2 (red) for centravac, 1comm3(red) for VAVI, 1comm3...
  20. Replies
    4
    Views
    493

    Trane VAV I protocol gateway

    Anyone know of a prtocol gateway available for the old Trave VAVI ucm's
  21. Replies
    2
    Views
    401

    analog output to analog input short

    Here was an interesting situation I ran into recently:

    ALC module (ME Controller) using its 0-10vdc analog output to another ALC (OEM I/O Zone controller) analog input set at 0-5v at In1. Both...
  22. Replies
    26
    Views
    6,768

    Any new reviews on this yet? How does it compare...

    Any new reviews on this yet? How does it compare with Ax or Struxureware?
  23. Replies
    4
    Views
    542

    non-JCI workbench for FX-60

    anyone know if a non-jci workbench laptop will work on an FX-60?
  24. Replies
    15
    Views
    14,261

    this file still avail? Cant find it on the site...

    this file still avail? Cant find it on the site - anyone have it?
  25. Replies
    21
    Views
    3,190

    any hint on the "secret code" thingy?:censored:

    any hint on the "secret code" thingy?:censored:
Results 1 to 25 of 163
Page 1 of 7 1 2 3 4
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event