Search:

Type: Posts; User: 7474

Page 1 of 4 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    15
    Views
    1,262

    Thanks, now I think I understand. So, the...

    Thanks, now I think I understand.

    So, the amp ratings on the appliances are what they draw per hour. Giving you kW hours.

    Thanks again, I appreciate your time and assistance.
  2. Replies
    15
    Views
    1,262

    I'm comfortable with the correct unit. ...

    I'm comfortable with the correct unit. Unfortunately, I seem to be getting a wide variety of answers.

    I would like to be comfortable with your number but I am having a difficult time...
  3. Replies
    15
    Views
    1,262

    Online generator sites say that the AC needs the...

    Online generator sites say that the AC needs the 17 or 20 from generac.

    Company 1 says Generac 17 at least, maybe 20.

    Company 2 says Generac 14 will handle AC no problem.

    From Generac...
  4. Replies
    15
    Views
    1,262

    Actually, 17 and 20 from Generac. I was asking...

    Actually, 17 and 20 from Generac. I was asking them about the 14 from Kohler based on what I read on Kohler's site. They said I would need 17 at least.
  5. Replies
    15
    Views
    1,262

    Little if anything. Stove, hot water, furnace,...

    Little if anything. Stove, hot water, furnace, dryer all gas.
    Everything else electric is small...furnace blower, fridge, freezer, microwave, dryer motor, washer, power vent for hot water,...
  6. Replies
    15
    Views
    1,262

    So, the hard start kit would really be of no...

    So, the hard start kit would really be of no benefit?
    Where does the 6.46 watt hours come from?
    7.5kW sounds a lot better on the checkbook than what the generator people were saying was needed....
  7. Replies
    15
    Views
    1,262

    Thanks for the reply. So, if my understanding...

    Thanks for the reply.
    So, if my understanding is correct. This compressor requires 23,280 watts to start (240v x 97amps)?
  8. Replies
    15
    Views
    1,262

    Lennox start assist

    Hello,
    Looking to purchase a standby generator for house.
    Have Lennox 13ACD Merit Series installed in 2006. Compressor locked rotor amp 97 and condenser fan locked rotor amp of 3.1.
    What affect...
  9. Replies
    2
    Views
    399

    Thanks.

    Thanks.
  10. Replies
    2
    Views
    399

    Wireless Thermostat

    Looking into wireless t-stat. Have Lennox GMP-51. Currently have Honeywell FocusPro 5000. Any recommedations would be greatly appreciated.
  11. Replies
    14
    Views
    2,758

    Thanks for the replies. I found that my system...

    Thanks for the replies.

    I found that my system is set to the defaults...
    heating 90 seconds (options include 30, 60, 90, 120, 180)
    cooling 2 seconds ( options were 2 or 45s)

    Left the heat at...
  12. Replies
    14
    Views
    2,758

    I am trying to determine if the fan should be...

    I am trying to determine if the fan should be running after the compressor stops or if it should stop at the same time as the compressor. Also, curious if the fan should stop at the same time flame...
  13. Replies
    14
    Views
    2,758

    fan off delay time

    Is there a standard time that the fan should run after the compressor stops on the air conditioner or during heating season after the flame stops in the furnace? Or, should the fan turn off the same...
  14. Thread: Measuring ESP

    by 7474
    Replies
    4
    Views
    434

    Thanks KEY1CC and PSTU, I appreciate the...

    Thanks KEY1CC and PSTU, I appreciate the information.
  15. Thread: Measuring ESP

    by 7474
    Replies
    4
    Views
    434

    Measuring ESP

    Following the thread "Getting the ESP" and watching the video by HVAC R US 2 I was wondering if anyone could recommend an inexpensive manometer for homeowner use. My curiosity has gotten the best of...
  16. xxxxx

    xxxxx
  17. Replies
    16
    Views
    1,101

    So the shorter times with the small temperature...

    So the shorter times with the small temperature difference (ID vs OD) are to be expected?

    The stat is set to 3 CPH (checked after seeing this in other posts)...the installers left the...
  18. Replies
    16
    Views
    1,101

    The thermostat is located on an interior wall...

    The thermostat is located on an interior wall (dining room), roughly the center of the house (2 story), above a floor return.
  19. Replies
    16
    Views
    1,101

    Honeywell FocusPro 5100 Lennox G51MP-48C-090...

    Honeywell FocusPro 5100
    Lennox G51MP-48C-090
    Lennox 13 ACD

    Thanks
  20. Replies
    16
    Views
    1,101

    Determining short-cycling

    I know that outside temperature affects AC runtime. I am trying to determine if the following is normal. At night with thermostat set to 72 and outdoor temp at 75, unit will run for approximately 5...
  21. Replies
    0
    Views
    277

    Determining short-cycling

    I know that outside temperature affects AC runtime. I am trying to determine if the following is normal. At night with thermostat set to 72 and outdoor temp at 75, unit will run for approximately 5...
  22. Replies
    113
    Views
    8,719

    I had the exact opposite happen. 2 techs, 2...

    I had the exact opposite happen. 2 techs, 2 separate occasions, tell me that they think Goodman is the best thing out there (since they bought Amana) ...as they serviced my Lennox, installed by...
  23. Replies
    8
    Views
    795

    I also was looking to change out my Focus Pro...

    I also was looking to change out my Focus Pro 5000 model. I was thinking of having the VisionPro installed but was wondering what benefits it could offer over the Focus Pro 5000 model I currently...
  24. Thread: Lennox question

    by 7474
    Replies
    20
    Views
    1,290

    Thanks for the info, it's appreciated. Will have...

    Thanks for the info, it's appreciated. Will have them bring out a blower motor also.
  25. Thread: Lennox question

    by 7474
    Replies
    20
    Views
    1,290

    Thanks for the assistance, it is appreciated.

    Thanks for the assistance, it is appreciated.
Results 1 to 25 of 83
Page 1 of 4 1 2 3 4
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event