Search:

Type: Posts; User: mjm88

Page 1 of 4 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    11
    Views
    848

    Accumulators are a great way to protect your...

    Accumulators are a great way to protect your compressor against liquid. Whatever reason it may be low loads, evap fan motors go out, txv gets stuck wide open. It's a good investment for the...
  2. Thread: digital gauges

    by mjm88
    Replies
    35
    Views
    2,215

    One of the first times I used my ak's I had the...

    One of the first times I used my ak's I had the wind catch a panel On a hussmann remote system and slam shut on the screen of the gauge. The only thing it did was put a small cut in the rubber boot...
  3. Replies
    1
    Views
    438

    Case temperature monitoring

    I have a customer that has asked for a way to remotely monitor case temps. These are just a few split systems and some self contained equipment. Looking for some ideas for the most affordable...
  4. Replies
    30
    Views
    3,343

    Haha we'll have to start pulling trailers

    Haha we'll have to start pulling trailers
  5. Replies
    30
    Views
    3,343

    I've heard the same thing about it being phased...

    I've heard the same thing about it being phased out due to high GWP ratings a few months ago by a local supplier
  6. Replies
    25
    Views
    2,515

    Well I have a system I'm trying to program on a...

    Well I have a system I'm trying to program on a press2temp sensor for and it's not available on the version of reflecs. I didn't know if I could update it to get that feature
  7. Replies
    25
    Views
    2,515

    . Is there a way to update the software on...

    .

    Is there a way to update the software on the reflecs controller with ultrasite?
  8. Replies
    15
    Views
    1,805

    I was just working on a Hussmann deli service...

    I was just working on a Hussmann deli service case today and they told me just the opposite. Set the Thermostat's to 28* discharge air, and set the EPR a few degrees below the evap setpoint so if a...
  9. Replies
    6
    Views
    1,291

    I've always had good luck with the strap wrench...

    I've always had good luck with the strap wrench on stuborn filters
  10. Thread: Hose Length

    by mjm88
    Replies
    17
    Views
    1,493

    This is why we never hook up to critically...

    This is why we never hook up to critically charged systems unless your positive you have a refer issue. Also probably why alot of critical system don't have access ports...
  11. Replies
    10
    Views
    879

    Yea it's a good way to ensure you don't plug up...

    Yea it's a good way to ensure you don't plug up the new one. Normally do a nitro purge as well to try and get any oil out of the evap and accumulator as well
  12. Replies
    10
    Views
    879

    We change the oil in the compressor with a...

    We change the oil in the compressor with a plugged cap tube and poe
  13. Thread: out of my realm

    by mjm88
    Replies
    43
    Views
    3,262

    I've :censored: up and last 400# of hp 80 before....

    I've :censored: up and last 400# of hp 80 before. **** happens as long as you learn from it. I was tol a long time ago it only a mistake the FIRST time
  14. Thread: out of my realm

    by mjm88
    Replies
    43
    Views
    3,262

    Same here. Just bleed the vapor out of the hoses

    Same here. Just bleed the vapor out of the hoses
  15. Replies
    10
    Views
    1,592

    you can get some milkstone remover at a farm...

    you can get some milkstone remover at a farm supply store. i wouldn't use it more than once though. then you will no doubt jack up the evap.
  16. Thread: out of my realm

    by mjm88
    Replies
    43
    Views
    3,262

    :ditto: Also like previously mentioned, learn...

    :ditto:

    Also like previously mentioned, learn the defrost cycle and your in there!
  17. Thread: Hand tools

    by mjm88
    Replies
    33
    Views
    2,607

    craftsman, gearwrench, and klien. Also a fan of...

    craftsman, gearwrench, and klien. Also a fan of the veto pro pac :cheers:
  18. Thread: A True Question

    by mjm88
    Replies
    9
    Views
    892

    It does come on there from the factory. We do...

    It does come on there from the factory. We do warranty work for true and i've seen it on a couple of the 72f units
  19. Replies
    18
    Views
    2,286

    Thats a good idea. When you walk up on a unit...

    Thats a good idea. When you walk up on a unit thats leaking on the stem and the plastic cap is cracked because someone put leak lock on it and cranked on it till it snapped. :gah:
  20. i've never seen a system messed up from dye. Not...

    i've never seen a system messed up from dye. Not saying it doesn't happen but i have never seen it. We do use dye. I personally try not to, but sometimes it is a good alternative. I carry the yellow...
  21. Replies
    3
    Views
    401

    We deal with multiple refrigerants day in and day...

    We deal with multiple refrigerants day in and day out and only carry one recovery unit on our trucks. We have never had a problem with it. I always make sure i purge the excess pressure out of the...
  22. Replies
    11
    Views
    1,083

    :yes: :yes: I have seen this more than once...

    :yes:

    :yes: I have seen this more than once cause intermittent freeze up's and it always does it overnight or when your not there. Can be extremley frustrating
  23. Replies
    558
    Views
    54,963

    Get an Allen wrench not sure what size and try...

    Get an Allen wrench not sure what size and try tightening up the fitting on the side. Took care of that problem for me
  24. Replies
    5
    Views
    775

    I don't think i'm opposed to anything right now.

    I don't think i'm opposed to anything right now.
  25. Replies
    5
    Views
    775

    I am no self employed, I am a refrigeration tech...

    I am no self employed, I am a refrigeration tech that currently works on anything from parrallel rack systems to soda dispensers. I have an associates degree from our local college in hvac/r tech. I...
Results 1 to 25 of 91
Page 1 of 4 1 2 3 4
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event