Search:

Type: Posts; User: hvamimi

Page 1 of 2 1 2

Search: Search took 0.01 seconds.

  1. Replies
    3
    Views
    1,180

    So basically just pull wires off old controller,...

    So basically just pull wires off old controller, terminate on new block, set the timing, and install the new flame scanner?
  2. Replies
    3
    Views
    1,180

    Cleaver Brooks flame safeguard

    Need to do a bid to replace a Cleaver-Brooks CB70 flame safeguard with a CB100E flame safeguard. Does anyone know what needs to be done on this after basic install? ie. programming, special setup...
  3. Replies
    10
    Views
    641

    Pink:D:D

    Pink:D:D
  4. Replies
    9
    Views
    2,658

    It is very likely that the heat exchanger will...

    It is very likely that the heat exchanger will crack if their is not enough airflow. Lack of airflow can cause the exchanger to reach a higher than designed temperature. That can be checked by...
  5. Replies
    126
    Views
    5,444

    Worked 2nd shift at Fratney st. school new...

    Worked 2nd shift at Fratney st. school new addition after school started to finish up all of the controls for a few weeks. If it wasn't for being able to park by the maintenance garage i'm sure I...
  6. Replies
    1
    Views
    1,802

    Tridium training

    Anyone know of any info. on Tridium other than stuff from Tridium? I am looking for an in general guide or some type of training in the form of a book or online.
  7. Replies
    18
    Views
    3,156

    TWO DAYS?!?! What can they possibly cover in...

    TWO DAYS?!?! What can they possibly cover in two days? I have Universal certification, spent probably four horus tops reading over the book than took the test.
  8. Replies
    126
    Views
    5,444

    There are many companies in town that bill a...

    There are many companies in town that bill a customer for 2 techs. to take the call in bad neighborhoods and the customer says that they won't pay for 2 techs. so they call someone else. I personally...
  9. Replies
    14
    Views
    1,510

    The more resistance you have will make the fan...

    The more resistance you have will make the fan work harder to push the same amount of air or the fan won't keep up and you will have a loss of air. Imagine blowing as hard as you can, like having no...
  10. If the job is done to code I doubt they will redo...

    If the job is done to code I doubt they will redo it for free. I would tell anyone you know who is considering any mechanical work about this though. Word of mouth will help get the idiots out of the...
  11. Replies
    8
    Views
    894

    Believe that Marter is right. That would get full...

    Believe that Marter is right. That would get full of lint quickly and than their would be no vent.
  12. Replies
    85
    Views
    4,264

    Do you own stock in Veto?

    Do you own stock in Veto?
  13. Their is no excuse for "splicing" flex!!! They...

    Their is no excuse for "splicing" flex!!! They should have removed the old piece if it was too short and installed a new piece. It would have taken no time and wouldn't have cost the contractor much....
  14. Replies
    3
    Views
    594

    School at night and helping during the day has a...

    School at night and helping during the day has a lot of benefits. You learn what tools are used and what the equipment is called. You won't learn how to replace a compressor, but you will know what...
  15. Replies
    3
    Views
    518

    Sounds like you are studying the right stuff, I...

    Sounds like you are studying the right stuff, I wouldn't get too much more in depth than that for now, but really learn the stuff that you're studying.
  16. Replies
    13
    Views
    1,678

    Milwaukee area around $35+ hr. if you negotiate...

    Milwaukee area around $35+ hr. if you negotiate with a reputable company and assuming that your controls experience is with large commercial and industrial buildings.
  17. One day while I was in class we took a break and...

    One day while I was in class we took a break and called One-hour with a few questions. 1) Are you NATE certified? They responded "We are certified." We asked "Are you NATE certified? They responded "...
  18. Replies
    6
    Views
    704

    Is it possible that the AHU in the basement heats...

    Is it possible that the AHU in the basement heats the whole house and the unit in the attic is A high-velocity space pac that is just for cooling? I don't know how common these systems are in the...
  19. Replies
    85
    Views
    4,264

    I too do controls work and have found it...

    I too do controls work and have found it difficult to find a good bag. Try Custom Leathercraft model 1526. It has a Grainger #3HY99 so you could look it up online and take a look at it.
  20. Thread: Which States??

    by hvamimi
    Replies
    10
    Views
    603

    Seems to me that air311 is right on. I have...

    Seems to me that air311 is right on. I have contemplated moving for work, but found the populated areas in Minnesota, Wisconsin, and Illinois to be the best after all factors. Makes sense, 90deg+ in...
  21. Replies
    5
    Views
    425

    I have done this before and it will work great!

    I have done this before and it will work great!
  22. Replies
    18
    Views
    1,480

    Typical non-union workday

    Typical non-union workday
  23. That should work pulling air through the return...

    That should work pulling air through the return and blowing it back out through the humidifier. Just make sure that it is interlocked so cooling and humidification aren't being done at the same time.
  24. Replies
    1
    Views
    518

    Just a different language between manufacturors...

    Just a different language between manufacturors and models. No difference between the two.
  25. Thread: Jci N30

    by hvamimi
    Replies
    27
    Views
    3,417

    I'm assuming you don't have access to HVACPRO....

    I'm assuming you don't have access to HVACPRO. You could call Johnson Tech. Support (800)275-5676 but they may tell you that you need to be an authorized rep to do licensing. In that case i'd just...
Results 1 to 25 of 35
Page 1 of 2 1 2
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event