Search Results - HVAC-Talk: Heating, Air & Refrigeration Discussion

Search:

Type: Posts; User: N2fords

Page 1 of 4 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    25
    Views
    803

    when was the last time you replaced the battery?...

    when was the last time you replaced the battery? Just a thought!
  2. Replies
    1
    Views
    221

    i like the H10 pm

    i like the H10 pm
  3. Replies
    2
    Views
    394

    I bet Positive and Neutral where reversed and you...

    I bet Positive and Neutral where reversed and you where see potential voltage always verify positive to ground to see which is in fact positive.
  4. I had a store that ran propane floor buffers and...

    I had a store that ran propane floor buffers and when they changed tanks in the same area of the Walk-ins it would alarm. for about 2 minutes. just a thought!
  5. voltage can kill compressors as well. how are...

    voltage can kill compressors as well. how are they failing?
  6. Replies
    18
    Views
    991

    a crane is about 150. an hour so why would you...

    a crane is about 150. an hour so why would you need to throw out your back carrying a comp up a ladder. that said I have roped up compressors to roofs where its not going to get their any other way....
  7. Thread: NATE Exam

    by N2fords
    Replies
    22
    Views
    698

    congratulations on passing. Remember to write...

    congratulations on passing.
    Remember to write down the # of the questions that you don't know and skip them go on answering the ones you are positive about.
    then later go back and I bet you can...
  8. Replies
    13
    Views
    961

    someone might of done it out of meanness

    someone might of done it out of meanness
  9. Replies
    13
    Views
    961

    someone closed it they do not close themselves.

    someone closed it they do not close themselves.
  10. Replies
    20
    Views
    1,072

    was it sideways and the unit was supposed to be...

    was it sideways and the unit was supposed to be up? if the relay is not mounted correctly it can do this.
  11. Replies
    11
    Views
    912

    Digicol AK900 I love it get the clamp on sensors...

    Digicol AK900
    I love it get the clamp on sensors as the velcro ones are a pain.
    Hope this Helps,
    Bruce
  12. Replies
    10
    Views
    970

    I ordered my Digicool AK900, BluVac (more costly...

    I ordered my Digicool AK900, BluVac (more costly one, Nylog, Appion Evac hose and core tool, &FieldPiece SPD2.
    All From TTT they always deliver the best. I Have been Pleased and would recommend them...
  13. Replies
    51
    Views
    2,334

    I am Assuming everyone here know never adjust a...

    I am Assuming everyone here know never adjust a txv until the box is within 5 degrees of set-point, right?
  14. the H-10 is without a doubt an awesome detector...

    the H-10 is without a doubt an awesome detector but so is my ultrasonic. I use both it I cant find it with these then I need to different job.
    Fix your H-10 and adjust your heaters, change the...
  15. If he is a good customer then I would Charge a...

    If he is a good customer then I would Charge a trip charge to cover time and fuel. if its a first time caller then I would charge him full price.
  16. Replies
    13
    Views
    1,049

    is the blower close to it rated amps? whats your...

    is the blower close to it rated amps? whats your return and supply air temps? where did you take the superheat to achieve the 18 degrees?
  17. Replies
    15
    Views
    1,069

    TruTechTools,I just did another order with them...

    TruTechTools,I just did another order with them and wont use anyone else.
    I have done 3 large orders already and have never regretted any of it.
    Great Shipping Service and its a Brother HVAC....
  18. Replies
    28
    Views
    1,588

    real simple measure the temperature of the inlet...

    real simple measure the temperature of the inlet water of both units. water source could be two separate lines where only one is bleeding do to mixing valve in plumbing gone bad, ohm out the sensor,...
  19. Replies
    16
    Views
    1,350

    I own the Blue Vac and I have not had a problems...

    I own the Blue Vac and I have not had a problems with mine but then again I never pressurized mine! just saying
  20. Replies
    81
    Views
    6,029

    Thank you sir! it always surprises me how little...

    Thank you sir! it always surprises me how little some people do! think of every job as if your boss will be the next guy working on it. Should change how some people do things.
  21. Chrismartian1978 We are mostly U.S. Technicians...

    Chrismartian1978 We are mostly U.S. Technicians so we don't know your countries requirements. So take that into consideration before slamming others for viewing your post.
    Also talk to people who...
  22. Replies
    81
    Views
    6,029

    another Rookie Mistake is hooking up your gauges...

    another Rookie Mistake is hooking up your gauges and seeing a low suction pressure and thinking its low on charge.
    Check your fan is on. check the evap is it frozen? filter Dirty, Evap or Condenser...
  23. Replies
    81
    Views
    6,029

    I had the power off on a self contained unit to...

    I had the power off on a self contained unit to check A liquid line solenoid I used a magnet to cycle the liquid line.. forgot to put the solenoid on and plugged the unit in. I was inside the 1 door...
  24. Just want to say if the hole is not in the right...

    Just want to say if the hole is not in the right spot after drilling use a wooden dowel to fill the hole and then finish it with whatever your drilling threw..
  25. Replies
    24
    Views
    1,108

    this is just me, but I always Change capacitors...

    this is just me, but I always Change capacitors with new motors. Cond may look clean and still be dirty.
    Whats your Voltage, any drop across the contactor. all wires tight. Fan located in the well...
Results 1 to 25 of 92
Page 1 of 4 1 2 3 4
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event