Search:

Type: Posts; User: southeflorida

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Same multimeter used everywhere. It has a thermo...

    Same multimeter used everywhere. It has a thermo coupler for temp taking. All temps were done twice.
    The supply vent is about 12ft from the return, on an opposite wall. The thermostat is 3-4ft...
  2. Sorry for the long delay in posting back. I'm out...

    Sorry for the long delay in posting back. I'm out of town again. To be honest I'm quite confused. Some of the responses I understand but some I just don't get. Static? Latent vs sensible? I need to...
  3. Problem with 2ND new unit. Temp won't go below 77

    Problem with 2ND new unit. Temp won't go below 77

    The company came out and installed a whole new system 2 days ago. It's a
    Ruud
    14AJM30 condenser (2 1/2 ton)
    RHLL-HM3617 air handler (3 ton)
    ...
  4. Just to update. They sent out a senior tech for...

    Just to update. They sent out a senior tech for one last look. Found the evap coil wasn't working properly. He showed me where some of the coils were icing up while some were not. He said he's never...
  5. Who? Me?

    Who? Me?
  6. And here's a HO's point of view. I wholeheartedly...

    And here's a HO's point of view. I wholeheartedly agree that a seasoned pro without Nate certification is very likely better then a 'chump' right out of Nate training. Problem for the HO is knowing...
  7. You bring up some interesting and valid points...

    You bring up some interesting and valid points udarrell. I'm sure my ducts need some fixin'...the house was built in '79. I will speak to them about it.

    As for the the new evap coil...it's a...
  8. Thanks for your inputs. I suspected it was...

    Thanks for your inputs. I suspected it was undersized and that's why I'd posted my original question. The company has been terrific...I have zero complaints about them and feel confident they'll get...
  9. I've got the "work sheet" he used for the load...

    I've got the "work sheet" he used for the load calc.
    Design based on:
    Outdoor 91F
    Indoor 75F/50% RH
    He measured all glass and doors and floor area sq footage. Factored in that glass is tinted...
  10. Load Calc says 2.28 ton. What way to go?

    What do you pros do when your load calc comes up with 2.28 ton? Would you size it up to a 2.5 or down to a 2 ton?
  11. Replies
    10
    Views
    2,454

    Thanks for the replies. They were here today (on...

    Thanks for the replies. They were here today (on another issue) and will be leveling it as he felt it was "too out of wack". Also said they do/will leave a slight off-level for drainage. Appreciate...
  12. Replies
    10
    Views
    2,454

    Will do

    Will do
  13. Replies
    10
    Views
    2,454

    I'm all for drainage away from the house. I read...

    I'm all for drainage away from the house. I read the installation instructions and Ruud just says to "ensure pad is level". It's the Ruud 14AJM. If being slightly off level is not an issue of...
  14. Is this the standard time it takes to flush the...

    Is this the standard time it takes to flush the lines, 2 hrs approximately? I just had my split system replaced and I didn't see anything hooked up that long...didn't see anything hooked up at all...
  15. Replies
    10
    Views
    2,454

    New condenser/pad not level

    Had a new split system installed and the condenser and pad are not level. Thought I'd read here somewhere that it's important that it is level but cannot find that thread. Was I dreaming or is it an...
  16. Get a Media Filter for a Florida 'snowbird'?

    Have been reading here for awhile and saw mention of the "media filters". I'm not really a 'snowbird' but I am in south Florida and am often away for extended periods (months sometimes). Do you think...
  17. Imtired: Have you found anyone for your new...

    Imtired:
    Have you found anyone for your new system yet?
    < No email addresses allowed in post, put it in your profile>
  18. I certainly understand that. I didn't get on him...

    I certainly understand that. I didn't get on him about it...just thought it was funny he'd ask for blue prints on a house he knew is 30yrs old. Maybe some folks DO have blue prints that old tho...I...
  19. Why put a Hard Start Kit on a new install?

    I'm in the process of getting a replacement split system. One of the quotes specifies installing a hard start kit on 2 of the 3 he quoted me on, both Rheems. The Lennox he'd written it in but crossed...
  20. Heck I had one guy tell me he needs the house...

    Heck I had one guy tell me he needs the house blue-prints! Yup, really.
  21. Oops. Sorry, seems I don't have PM here either....

    Oops. Sorry, seems I don't have PM here either. My email is in my profile...click on "southeflorida" up in the left corner of this post and you'll get to that page.
    Casey
  22. Replies
    7
    Views
    1,343

    Score the fat deeply. Marinade first in equal...

    Score the fat deeply. Marinade first in equal parts olive oil and basalmic vinegar, and some fresh ground black pepper. Add rosemary or oregano if you want. Do mine deboned and butterflied (like it...
  23. I'm in the West Palm area (Jupiter) and looking...

    I'm in the West Palm area (Jupiter) and looking to replace a system right now too. Read what "Dash" advised me to do when I posted a few days ago

    http://hvac-talk.com/vbb/showthread.php?t=569442...
  24. posting current quotes

    Thanks Dash. You were a big help a few years back when we replaced our other system. This board was a wealth of great advice as a matter of fact.
    Reason I'm here asking about installers is because I...
  25. Looking for installer recommendation in West Palm Beach,FL

    We've decided to replace our old split system. Can anyone recommend a quality installer in the West Palm Beach, Fl area?
    Most appreciated.
    Casey
Results 1 to 25 of 52
Page 1 of 3 1 2 3
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event