Search:

For your information, we do have a Selective Service law now. If you have a kid 18 years old they have to register. The law states that if a draft were enacted, there would be no deferments for...

Above is quoted another republican that has never served and has no idea what the military is like or how they operate. If there was a draft, where everyone can be drafted, then our Armed Forces...

You know I have to take my hat off to the Republicans because they have been extremely successful in convincing all you hard working, blue collar workers that they are one of YOU.

Their media...

1. Chill bill, why do you have to call someone a faggot??

2. You are the first person I have known that thinks 40 percent is a majority. It aint' good cuz.

You guys act like you were born knowing pneumatics, give the guy a break.

This post is to help people not ridicule. This is a forum to learn, if you want to ridicule people then get a job doing...

I have emailed them. Still waiting for a reply HVAC 3901. I sent it Thursday, so I can't call them slacking just yet.

Thanks Maxter. I looked at ebay, but they didn't have one either.

Why use the Tool 100-500. Because we have one. I am new to the shop, we have one, it has seldom been used. I am not a super...

Any one know where to get detailed information such as pdf files for Barber-Colman pneumatic controls

[Edited by hvac-alan on 02-25-2006 at 03:07 PM]

My email address is hvac-alan@nc.rr.com

Thanks a bunch!!!!

Looking for a website to get the instruction manual for the Barber Coleman Pneumatic Calibration Panel (Tool 100-500) Any ideas??? I have tried Invensys website. No cigars.

I am looking for a website to download a instruction manual for a Barber Coleman Siebe Pneumatic Calibration Panel (Tool 100-500). I have tried Invensys website but cannot find a link to any pdf...

I agree with the formula cited above. Also if you have the info on the evaporator, there should be a chart that you can use to calculate it. This normally requires measuring the pressure drop across...

It has been a while, but Chill Bill revived this thread and I noticed that I did not give comment on the converter and using the little Dos program to watch all the temperature inputs.

I have used...

Chill Bill

Would be happy to send the little program, but can't find your email address in your profile, please advise

mine is hvac-alan at nc.rr dot com

Alan

EDIT: No email addies...

Hvacpope What is a liberal exactly????

Server room it is all about helping people. I have learned alot from this thread and I appreciate the fact that you kept us informed and stayed involved in the thread so we could get some needed...

I had a simuliar problem with intermittent trips on a flowtronic chiller. The problem progressed until I started getting a chattering on the fan and compressor contactors before it locked out on 51....

Been there,

I would like to see the formula where you can determine static pressure with the known variables of vp and friction. I wasn't aware that you could get that from the information...

Have you tried to get some fan data from the manufacturer of the fan. Most have charts that will tell you what the CFMs will be at a certain static pressure. I would think that you could use the...

If you are looking for a book answer, then it depends on the type of building and the activiy being done like sparks has indicated.

A chart for all these can be found in Table 10 of Manual N...

Hello all,

Thanks for all your input. I went back today and went through the Carrier EXV troublshooting suggestions. Before that, I verified that the EXV was the correct one. It was. Checked...

Thanks John:

That clears up the confusion I had with the number of steps this motor has. I have read in the historical part of this site that these type problems have occured when the incorrect...

Hey ac eagle

I am going back Tuesday. I am hoping the converter will be here soon, but I will have to start without it. I will check and double check the sensors and make sure they are wired...

Hey ac eagle

The board has not been replaced. Though it may turn out that it needs to. The literature and several guys on this site have mentioned an exv driver board. I am fairly certain that I...

MMC

You have been a great help. You have filled in the part that I did not understand. I haven't been in commercial too long (1 year) and most of the guys in my department are far more advanced...