Search:

Type: Posts; User: hw chiller man

Page 1 of 7 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    0
    Views
    379

    19XR Lid2 for sale

    I have a 19XR lid2 for sale recently removed on a retrofit job.
    The module part number is 19XR04005001. Make a fair offer and its yours.
  2. Replies
    26
    Views
    7,286

    It was rebuilt, with eddy current testing, both...

    It was rebuilt, with eddy current testing, both by York. York gave a 90 day warranty knowing the chiller hardly runs and this satisfied the customer. As you can see its been running for 7 years now...
  3. Replies
    26
    Views
    7,286

    Here are some pictures of different chiller...

    Here are some pictures of different chiller failures319641319651319661319671
  4. Replies
    8
    Views
    1,163

    Schedule 10 stainless, I got approval to use from...

    Schedule 10 stainless, I got approval to use from Trane on an air cooled remote evaporator installation. Project did not happen. the pipe was going to be welded and cleaned as required. The weight is...
  5. Replies
    36
    Views
    3,175

    This may or may not help you AC. I officially...

    This may or may not help you AC. I officially retired from the UA on January 1, 2010. I received all my pension money and rolled it into an RRSP as required under Canadian law. I now have control...
  6. Replies
    153
    Views
    38,767

    Tried to send the form but was rejected by your...

    Tried to send the form but was rejected by your server
  7. Replies
    153
    Views
    38,767

    Hi Abs Would you be kind enough to email me...

    Hi Abs

    Would you be kind enough to email me the form, I tried getting it
    from JCI directly, no luck. My email is Email Address Removed

    best regards..........wayne
  8. Replies
    10
    Views
    1,404

    Thanks for the reply. I don't have a diagrahm in...

    Thanks for the reply. I don't have a diagrahm in front of me but I thought the unload signel came directly from the compressor controller. This is a Microtech II retrofit.
  9. Replies
    10
    Views
    1,404

    Low evap temp

    Low evap temp
  10. Replies
    4
    Views
    1,145

    You can get the most oil out of the vessel by...

    You can get the most oil out of the vessel by closing the valve upstream of the internal oil filter and front seating the service valve upstream of the inline filter. Remove the oil from the service...
  11. Replies
    4
    Views
    1,145

    Be careful with that switched. I replaced one...

    Be careful with that switched. I replaced one this week because we had oil at the schraeder on the bottom of the vessel but the switch would not make. Replaced switch, inspected old one and it worked...
  12. Replies
    10
    Views
    1,404

    Set point is 44F Flow is at design Not sure on...

    Set point is 44F
    Flow is at design
    Not sure on liquid level
    Sensor reads correctly when the chiller is running properly and when this issue happens.

    Perhaps I didn't explain thoroughly. As the...
  13. Replies
    10
    Views
    1,404

    McQuay Chiller Low Temp Shutdown

    We have a site with two McQuay PEH067 chillers. The micros were changed out a few years ago by McQuay service and have operated flawlessly since then. Recently one of the chillers started shutting...
  14. Replies
    22
    Views
    1,495

    Thanks for the info

    Thanks for the info
  15. Replies
    22
    Views
    1,495

    I remember that picture. Also thought the Vacinol...

    I remember that picture. Also thought the Vacinol was great. Mine always seemed to crack around the plastic casing and the numbers would wash off. The idea was great, the apparatus was not so good,...
  16. Replies
    22
    Views
    1,495

    Is this the picture with the wet bulb indicator...

    Is this the picture with the wet bulb indicator attached to the chiller?
  17. Replies
    22
    Views
    1,495

    I believe the 5000 microns comes from the days...

    I believe the 5000 microns comes from the days when York and Carrier used a wet bulb indicator to measure vacuum. If I remember correctly, we tried to achieve a reading of -12F (methyl alcohol)...
  18. Haven't seen that York in over a year, they...

    Haven't seen that York in over a year, they stopped paying there bills and we were outa there like mice jumping off a sinkin ship. I thought for sure you guys were doing it.
    The McQuay is no big...
  19. That was indeed the problem. I went to a...

    That was indeed the problem. I went to a different site to check that line and saw the 250 followed by 0000 which is the actual current. Went to my site and there was no 250, all 0's, I entered the...
  20. Thanks Rick I will try that today.

    Thanks Rick

    I will try that today.
  21. HELP!!! Microtec II motor current troubles

    I installed a Microtec II panel last winter on a PEH 087 chiller. The weather has finally warmed so that the micro can be comissioned. All operation appears satisfactory except for the motor current...
  22. Replies
    5
    Views
    978

    I believe the panel is 1996 vintage according to...

    I believe the panel is 1996 vintage according to the serial number.
  23. Replies
    5
    Views
    978

    I'll have to check the year on monday, I removed...

    I'll have to check the year on monday, I removed the model and serial number plate and installed it on the new micro. I will break it down as I have already stated but I want to sell all components...
  24. Replies
    5
    Views
    978

    McQuay service quoted to do the job of installing...

    McQuay service quoted to do the job of installing the new panel and was offering a credit of $3000.00 for the old panel. I'd say $500 plus shipping costs would be a good starting point. I'll remove...
  25. Replies
    5
    Views
    978

    McQuay Microtech 100

    This panel was recently removed from a PEH 087 chiller and was completely operational. Best offer
  26. Replies
    4
    Views
    756

    Thanks Abs, I will be back at the site on monday...

    Thanks Abs, I will be back at the site on monday and give it a try. The only calibration that I could see was the buttons to the bottom right of the screen....but they all seemed to only deal only...
  27. Replies
    4
    Views
    756

    Help with McQuay touch screen

    Is there a procedure for calibrating the Microtech II touch screen. The touch part of the screen is off a bit. Presently I have to touch the screen about an inch above the area that I need to, to...
  28. Replies
    10
    Views
    1,182

    This is an automobile assembly plant. The...

    This is an automobile assembly plant. The customer has many issues with how the water is used in his process. All of these issues would require his personnel to repair. It is much easier on his part...
  29. Replies
    10
    Views
    1,182

    Combination of both at various times. Customer...

    Combination of both at various times. Customer insists on running 38F water and has had tower issues over the summer at various times.
  30. Replies
    10
    Views
    1,182

    Thanks for the reply Richard....... its what I...

    Thanks for the reply Richard....... its what I suspected
  31. Replies
    10
    Views
    1,182

    Sorry guys, would have thought the "keyless...

    Sorry guys, would have thought the "keyless micro" would have distinguished this panel from the optiview panel. It is a single speed compressor, was looking to see if any yorkies know of an eprom...
  32. Replies
    10
    Views
    1,182

    York Surge Protection

    I apologize to anyone reading this in the refrigeration forum - obviously my mistake.
    Is there any way to provide surge protection for a York chiller using the keyless panel. Does the latest eprom...
  33. Replies
    0
    Views
    408

    York Surge protection

    Is there any way to get surge protection in a York keyless panel. I know it is available for the Optiview but wondered if surge protection was written in to the latest eproms for the older keyless...
  34. Replies
    16
    Views
    1,573

    I used to do 10 major inspections (overhauls) per...

    I used to do 10 major inspections (overhauls) per winter. I haven't done one now in two winters which is fine with me since I spend my winters golfing in Florida. But this is good warm work I could...
  35. Replies
    14
    Views
    1,459

    I received pricing today, the kit comes complete...

    I received pricing today, the kit comes complete with or without the touchscreen (don't know why anyone wouldn't want the touchscreen). Software preloaded and install instructions. I will be...
  36. Replies
    14
    Views
    1,459

    Thanks for all the replies guys, I'm working on...

    Thanks for all the replies guys, I'm working on it, I have a part number and will propably have pricing and availability by monday. It appears that it is available thru the States.
  37. Replies
    14
    Views
    1,459

    Microteck 100 upgrade

    I have a PEH 067 chiller that I have been servicing for approximately 14 years. The customer has finally found some budget money to replace the original Microtek 100 controller. I have received...
  38. Replies
    6
    Views
    1,027

    Hey BB.........whats the spray paint for?

    Hey BB.........whats the spray paint for?
  39. Replies
    18
    Views
    2,251

    Thanks for your excellent response Richard, I was...

    Thanks for your excellent response Richard, I was hoping you in particular would chime in. I will inspect the labys tomorrow to determine the clock position of the most wear on each laby. In your...
  40. Replies
    18
    Views
    2,251

    York YK Teardown Issues

    We have just completed a YK teardown in our shop and this being my first one I have a few questions. The compressor was torndown for a number of reasons......excessive excelleration time on startup,...
  41. Thanks HMD.......got the compressor parts book...

    Thanks HMD.......got the compressor parts book and found what you were explaining for the YT.......the YK has an external oil feed line so I suspect its seal cavity is at system oil pressure.
  42. Help me out here guys....never heard of this seal...

    Help me out here guys....never heard of this seal pressure cavity thing. How is this different from main oil pressure which I normally see between 30 to 35 PSID. How is the seal cavity pressure...
  43. Replies
    39
    Views
    4,293

    What were you doing up at 6:45 this morning.... I...

    What were you doing up at 6:45 this morning.... I was working on my 4 handicap, you were misinformed by some chiller mechanic who can't get enough time to work on his game.......ha...ha...ha.....wayno
  44. Replies
    39
    Views
    4,293

    I'M 57 and looking to go in two years...

    I'M 57 and looking to go in two years MAX.......am only working 3.5 days during the week and am able to take off for 4 months in the winter.....a sweetheart deal I am very satisfied with. Our company...
  45. Replies
    7
    Views
    819

    The tank does not need to be sized for the entire...

    The tank does not need to be sized for the entire fluid capacity. I would install a wier (hope thats the proper spelling) where the fluid enters the tank. The weir would consist of a vertical loop...
  46. If the oil heater is bad a new can be installed...

    If the oil heater is bad a new can be installed without compressor dissassembly. Remove the oil and the oil pump-filter assembly. The existing heater may need to be bent up to remove but the...
  47. Replies
    50
    Views
    4,314

    The Roberts Group........excellent guys to work...

    The Roberts Group........excellent guys to work with.
  48. Hey Chilly Sorry buddy, I couldn't resist any...

    Hey Chilly
    Sorry buddy, I couldn't resist any longer.....I can't believe you fell for it. I fully expected your first response (which was great by the way) was your last. I've been lurking in the...
  49. Replies
    50
    Views
    4,314

    I work for Honeywell (hence the HW) and am in...

    I work for Honeywell (hence the HW) and am in Windsor. The Campbellville Mushroom Farm owner, is a customer of ours in this area. They bought the farm and we became involved in the first upgrade. It...
  50. Replies
    50
    Views
    4,314

    Thanks for the vote of confidence SS......been...

    Thanks for the vote of confidence SS......been servicing centrifugals for 30 years and I too would not start any chiller that is not installed properly. Don't know who you work for but this chiller...
Results 1 to 50 of 340
Page 1 of 7 1 2 3 4
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event