Search:

Type: Posts; User: d_d_c_jci

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    16
    Views
    1,285

    The architect and customer preferred this wiring ...

    The architect and customer preferred this wiring
    scenerio because it is a datacenter if NCM or DX
    goes down they want local control.

    The first thing I thought was the AI to AO scenerio
    but...
  2. Replies
    24
    Views
    4,661

    lenb: Check your email for further...

    lenb:



    Check your email for further instructions.
  3. Replies
    24
    Views
    4,661

    When you run that patch it will upgrade you ...

    When you run that patch it will upgrade you
    from 8.07 to 8.08B. You do not need anything else.
  4. Replies
    24
    Views
    4,661

    lenb: Check your email.......

    lenb:


    Check your email.......
  5. Replies
    16
    Views
    1,285

    1 DA sensor and 2 DX-9100

    Have 2 fans and 2 DX-9100 controllers.
    The fans go to a common duct.
    They have separate discharge sensors.
    If I installed a 4-20ma discharge sensor
    in common duct, can I wire it to both DX-9100?...
  6. Thread: NCM Demon??

    by d_d_c_jci
    Replies
    23
    Views
    1,178

    Usually on the blue screen, you single click on...

    Usually on the blue screen, you single click on the system
    that the processes have been programmed for (AHU1, 1stfloor,etc)
    It depends where they created the processes in Metasys.
    , then on bar on...
  7. Replies
    7
    Views
    746

    The only thing I know of for DX power failures is...

    The only thing I know of for DX power failures is below:

    Is there a program for DX power failures?

    Cause:

    Solution:
    See the Pwrfail.exe and Reset.exe files located in the DX-9100 Tools...
  8. Thread: N30 Error

    by d_d_c_jci
    Replies
    17
    Views
    1,466

    Have you tried to connect with hyperterminal?

    Have you tried to connect with hyperterminal?
  9. Thread: NCM Demon??

    by d_d_c_jci
    Replies
    23
    Views
    1,178

    Sounds like GPL is using an Analog Data point to...

    Sounds like GPL is using an Analog Data point to write
    the setpoint in CS object.
    Go to processes in Metasys and see if there is a process called
    setpoints or something like that.
    If GPL files...
  10. Replies
    4
    Views
    735

    OK...but what about from the server. I cannot...

    OK...but what about from the server.

    I cannot look or modify the program from
    the server if it wasn't in Visuallogic?
  11. Replies
    4
    Views
    735

    Alerton programming

    I have a school district with Envision for Bactalk on a server.
    Each school has at least 1 TUX, ETH, etc.
    The field controllers vary because they were installed
    when they had IBEX.
    I know I can...
  12. Replies
    24
    Views
    4,661

    Here you go....

    Here you go....
  13. Replies
    13
    Views
    1,042

    Thanks again for your responses.... I will get...

    Thanks again for your responses....
    I will get pricing tomorrow on MP580
    Can it be programmed through a Summit workstation?
    I have Lonmaker but if I can use the workstation
    it would be better.
  14. Replies
    13
    Views
    1,042

    No Lon, Only Comm3, Comm4, and Comm5 on BCU. ...

    No Lon,

    Only Comm3, Comm4, and Comm5 on BCU.

    MP581 might be too much.

    This is the reason why I thought UPCM and now
    you guys just reinforced my thoughts.
  15. Replies
    13
    Views
    1,042

    Boiler controls

    What Trane controller is best for turning boilers
    on-off and controlling secondary valve?
    Would it be UPCM?
    We have Trane Summit BCU with workstation.
  16. Replies
    4
    Views
    549

    How do I find / modify the IP address for Summit?

    How do I find / modify the IP address for Summit?
  17. Replies
    4
    Views
    549

    N31 integration

    Has anyone tried to bring the N31 into Tracer Summit
    as BACNET/IP?
    How hard is it?
    Is there a point limit?
  18. Replies
    12
    Views
    885

    Your HVACPRO settings are fine. You need to...

    Your HVACPRO settings are fine.

    You need to change your jumper on your actuator to
    reverse-acting. But make sure when you lose
    power to the actuator it spring returns open.
  19. Replies
    11
    Views
    7,434

    NAE and NCE are different controllers so THERE IS...

    NAE and NCE are different controllers so THERE IS NOT a NAE25.
  20. Replies
    11
    Views
    7,434

    There is no NAE25, only 35,45, and 55. Anyways,...

    There is no NAE25, only 35,45, and 55.
    Anyways, there is no simple way to reset passwords
    without blowing the database away. (N.U.T. the NAE)
    Then reloading it.
    Are you sure you typed in the...
  21. Replies
    3
    Views
    530

    Yeah, but the problem is when maintenance turns...

    Yeah, but the problem is when maintenance turns the
    univent off to change filters the command from the n30
    goes away and defaults to summer until the master is toggled.
  22. Replies
    3
    Views
    530

    N30 Interlock

    Have some univents with UNTs
    that has sum-win binary input
    I am using the N30 master sum-win
    to override these inputs.
    When univents lose power and come back
    on, they default to summer because...
  23. Thread: NAE graphics

    by d_d_c_jci
    Replies
    3
    Views
    860

    NAE graphics

    Does anyone have RTU, MAU, and VAV w/electric heat
    graphics that they can share?
    Either standard or advanced.
  24. Thread: Dectron

    by d_d_c_jci
    Replies
    12
    Views
    2,931

    Dectron

    Has anyone tried to integrate into a Dectron
    unit that has a Siemens OP393 III PLC controller?

    Anyone know what the controller's protocol is?
  25. Replies
    7
    Views
    987

    gbfromsd NO...why?

    gbfromsd


    NO...why?
Results 1 to 25 of 184
Page 1 of 8 1 2 3 4
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event