Search:

Type: Posts; User: zlotvor

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    7
    Views
    533

    Sorry for late response. No, straight to the...

    Sorry for late response.

    No, straight to the USB.
    It's in datasheet:
    http://www.bacnetinternational.net/catalog/manu/siemens/149206_PXCCompact_3.2.pdf
  2. Replies
    6
    Views
    523

    I don't understand completely what you exactly...

    I don't understand completely what you exactly need. Does you need recommendation on KNX/IP to Bacnet/IP or on all devices installed?

    For the KNX/IP to Bacnet/IP, there is a whitepaper describing...
  3. Replies
    7
    Views
    533

    USB port supports the same functionality. It's...

    USB port supports the same functionality. It's easyer to source USB cable ;)
  4. Replies
    39
    Views
    2,813

    Quality equipment can easily pass the 10-15 years...

    Quality equipment can easily pass the 10-15 years or more of service if properly maintained. I have a site with dozen of Siemens PRV2 controllers, and even nobody touched it for ten years they still...
  5. Hi, I'm not sure what are you trying to do,...

    Hi,

    I'm not sure what are you trying to do, but if my memory serves me correctly, there is a very easy way of integrating Sinteso panels into Desigo Isnight. I'll check it and come back later.
    ...
  6. Replies
    8
    Views
    478

    Thanks all for your inputs. If the investor...

    Thanks all for your inputs.

    If the investor agrees the BX300 will be terminated and replaced.
  7. Replies
    8
    Views
    478

    Hi jpsmith1cm! Thank you for your answer! I've...

    Hi jpsmith1cm!

    Thank you for your answer! I've realized that BX300 is of "canned" type with predefined applications already installed.
    But I cannot beleive they did not prepared some type of...
  8. Replies
    8
    Views
    478

    Hi WillyTech, First I have to apologize not...

    Hi WillyTech,

    First I have to apologize not responding earlier.

    I have no idea what communication protocols are supported by this device. Emmerson had still not responded to my question (where...
  9. Replies
    8
    Views
    478

    It is not possible that nobody is familiar with...

    It is not possible that nobody is familiar with this (Emerson CPC BX300).

    I have two options with this controller
    1) Integrate it with your help (Emerson is of no help) - cheaper to end user
    ...
  10. Replies
    10
    Views
    819

    Hi Vas, Please post the schematic of your...

    Hi Vas,

    Please post the schematic of your connected devices. Otherwise nobody can tell you exactly what to look for. All of the above comments are general, based on someones previous experience.
  11. Replies
    10
    Views
    819

    But there MUST be one point of reference, and...

    But there MUST be one point of reference, and it's the easiest way to get it trough ground. Transformers have the hot and the neutral just like mains power, and until you take care not to ground the...
  12. Replies
    10
    Views
    819

    When your devices are powered from different...

    When your devices are powered from different sources, most of the times there is a voltage difference between grounds. Check that all the grounds (or negative polarities) are on same potential. ...
  13. I've been strugling with that kind of cable...

    I've been strugling with that kind of cable before. Conclusion is that they do NOT work! Most of them is made to look like a printer port to use with a printer only.

    For Hardlock/Sentinel/etc...
  14. Replies
    8
    Views
    478

    Emerson CPC BX300 vs Desigo Insight

    Hi,

    I've been asked if this thing can be visualised in Desigo. Do anyone can provide me some information on this one?
    Is it even possible to connect to it?

    br, Z
  15. Thread: Siemens RWX62

    by zlotvor
    Replies
    11
    Views
    1,969

    Hi Loopy I have a software, but no cable...

    Hi Loopy

    I have a software, but no cable schematic. The software is still available free of charge, just send me a email.
  16. Thread: Siemens RWX62

    by zlotvor
    Replies
    11
    Views
    1,969

    Ok, I've successfully located a source of that...

    Ok, I've successfully located a source of that program. If you need it drop me a mail. Free of charge, of course.
  17. Thread: Siemens RWX62

    by zlotvor
    Replies
    11
    Views
    1,969

    Then upload the copy of the disk to the internet...

    Then upload the copy of the disk to the internet so one can verify that the disk is in usable state.
  18. Thread: Siemens RWX62

    by zlotvor
    Replies
    11
    Views
    1,969

    Hi, Sorry to disappoint you, but I was unable...

    Hi,

    Sorry to disappoint you, but I was unable to locate any source of software or documentation that will help you. It seems that people who has done work on this controller are out of service or...
  19. Replies
    13
    Views
    2,770

    Just made a short starter video on MBSheet /...

    Just made a short starter video on MBSheet / MBConf usage:

    http://youtu.be/d2UwLoX5LT0

    Please forgive me absence of music/narration ;-)
  20. Thread: LonData Points

    by zlotvor
    Replies
    7
    Views
    827

    Hmm, maybe I should google around before posting....

    Hmm, maybe I should google around before posting. First one:
    http://www.niagara-central.com/ord?portal:/blog/BlogEntry/247
  21. Replies
    1
    Views
    419

    Did you tried 0xCF address? The read telegram...

    Did you tried 0xCF address? The read telegram telegram should look like (if meter address is 1) 01 03 00 CF 00 02 XX.
    You should receive something like this 01 03 04 AA BB XX.
    Where XX is CRC, AA...
  22. Thread: LonData Points

    by zlotvor
    Replies
    7
    Views
    827

    The conversion formula is simple: C x 9/5 +...

    The conversion formula is simple:
    C x 9/5 + 32 = F or
    C x 1.8 + 32 = F

    I'm confused with "PX pages". Did you mean Desigo PX?
  23. Replies
    3
    Views
    750

    Quote to myself, Sorry, the integration job...

    Quote to myself,

    Sorry, the integration job was canceled, due to not finished mechanical works on the boilers.
  24. Replies
    13
    Views
    2,770

    Did you manage to get any data? I can check this...

    Did you manage to get any data? I can check this personally if you can provide remote access (teamviewer or similar), my time is GMT+2

    I'm not familiar with Mango, so in that one you should find...
  25. Replies
    13
    Views
    2,770

    Forget about Rac's software, in demo mode it's...

    Forget about Rac's software, in demo mode it's just unusable. I'd recommend you the MBsheet/MBconf pair. It say DEMO, but in reality only the comfort features are disabled.

    Try to search with...
Results 1 to 25 of 41
Page 1 of 2 1 2
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event