Search:

Type: Posts; User: grovecreek

Page 1 of 6 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    1
    Views
    168

    So I went into Zones advanced area and changed...

    So I went into Zones advanced area and changed the priority array 13 to 12 and this took care of the problem. Something is writing to that priority on 13 but could not find where. Working good now.
  2. Replies
    1
    Views
    168

    Alerton Schedules

    I have one Heat Pump where the schedule keeps going unoccupied on the zone. All the other Heat Pumps on the same Global zone work fine ?
  3. Thread: DDC Toolbar

    by grovecreek
    Replies
    0
    Views
    278

    DDC Toolbar

    Working with DDC toolbar and was wondering if you can update your point data offline using your laptop offline away from the job ? I am just trying to make changes on the existing visio file on my...
  4. Thread: Alerton

    by grovecreek
    Replies
    0
    Views
    210

    Alerton

    Does anybody have any programming code to slave 3 out of 4 vav's. Most of it would be transfers in the global code.
  5. Thread: Alerton VLC

    by grovecreek
    Replies
    2
    Views
    571

    Yes I could try that tomorrow.

    Yes I could try that tomorrow.
  6. Thread: Alerton VLC

    by grovecreek
    Replies
    2
    Views
    571

    Alerton VLC

    Controller VLC SD2A has solid green light on led. It should have a 3 flash instead. I checked MAC address and has correct address on dip switches but still stays a solid green lights. This device is...
  7. Replies
    3
    Views
    744

    The global code for this bcm should be 112000 but...

    The global code for this bcm should be 112000 but it is no where to be found.
  8. Replies
    3
    Views
    744

    Alerton Envision

    Building I am working in network number for these devices are 112 but i cannot find global code with these numbers at all. I went through all the ddc code and found nothing. Is there a way to find...
  9. Replies
    4
    Views
    761

    Thanks guys it was the IP address conflict that...

    Thanks guys it was the IP address conflict that was causing the issue. Working good now.
  10. Replies
    4
    Views
    761

    BASRTP-B BACnet router

    My laptop I use with this device has been working fine until lately. I need to go into the settings to change my network number but i cannot get the router config page to open. I have windows 7 does...
  11. Thread: Visiologic

    by grovecreek
    Replies
    3
    Views
    942

    Yes thank you for the advice. I was looking at...

    Yes thank you for the advice. I was looking at alerton standard bitmaps and prog and was trying to find some smaller code to go over and work with.
  12. Thread: Visiologic

    by grovecreek
    Replies
    3
    Views
    942

    Visiologic

    What is the way to learn how to write code in visio. Are there any good books or online training Thanks
  13. Replies
    5
    Views
    577

    Yes I agree just wondering if anyone has had...

    Yes I agree just wondering if anyone has had issues with this model controller flame rod and grounding are good.
  14. Replies
    5
    Views
    577

    Flame sense problem

    Our Church has two Weil Mclain boilers model number is cp3513605 I cannot get micro amp reading any higher than about .80 amps. We ran new ground wire back to control panel and still nothing. I...
  15. Replies
    1
    Views
    440

    Samsung mini split

    This system is about 5 years old, I don't have the model or serial number at this time. It is a cooling only with two power heads, in the past I had freon leaks every season but not this year. This...
  16. Replies
    8
    Views
    616

    There is glycol in the system now but I will have...

    There is glycol in the system now but I will have to test to see where I am at now.
  17. Replies
    8
    Views
    616

    Thanks for the advise.

    Thanks for the advise.
  18. Replies
    8
    Views
    616

    I work on rtu most of the time can you give me...

    I work on rtu most of the time can you give me some advise.
  19. Replies
    8
    Views
    616

    Boiler Questions

    I have not worked on a comercial boiler in quite a while. Today at my church I was trying to replace the low water cut off. There was no room to work on this it was very hard to get union nuts loose....
  20. Replies
    19
    Views
    3,660

    Today I installed my first True steam humidifier....

    Today I installed my first True steam humidifier. The controls were true IAQ setup every time I seem to install these the outdoor sensor it is always reading way off on temp. The sensor was all the...
  21. Replies
    19
    Views
    3,660

    The furnace is in a closet space that is...

    The furnace is in a closet space that is insulated up in the attic area. So we don't have to worry about freezing in that area.
  22. Replies
    19
    Views
    3,660

    This installtion is up in a attic space with no...

    This installtion is up in a attic space with no floor drain to work with. Just a condo pump to discharge the water. That is what concerns me is the hot water when it discharges into pump.
  23. Replies
    19
    Views
    3,660

    I just want to make sure the condensate pump can...

    I just want to make sure the condensate pump can handle the temp of the water and discharge amount.
  24. Replies
    19
    Views
    3,660

    True Steam Humidifier

    Does anybody know if the 6 gal true steam Honeywell humidifier can discharge water into a condo pump? It sounds like they discharge quite a bit of water at one time. Thanks Grove
  25. Replies
    1
    Views
    399

    co test spray

    Does anybody no where a person can purchase some test spray in a can.?Aprilaire does not carry this product no longer.
Results 1 to 25 of 138
Page 1 of 6 1 2 3 4
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event