Search:

Type: Posts; User: Mooshman812

Page 1 of 9 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    3
    Views
    140

    Ouch, I'm 24 and not sure whos got it worse.

    Ouch, I'm 24 and not sure whos got it worse.
  2. Also 1/3hp r12 has more capacity than the same...

    Also 1/3hp r12 has more capacity than the same using 134a.... I believe.
  3. Why did you opt out of txv? Also did you size cap...

    Why did you opt out of txv? Also did you size cap tube for r12 on accident?
  4. Replies
    14
    Views
    443

    At least you can see something, it looks like my...

    At least you can see something, it looks like my image was removed. Dont think I remember seeing one either. Hillbilly can you post your diagram, just for my own peace of mind.
  5. Replies
    14
    Views
    443

    Thats all the more the manual on parts town lists...

    Thats all the more the manual on parts town lists for errors, 1-8 is all. I wish there was a follow up!
  6. Replies
    19
    Views
    1,129

    That was always kinda my thoughy. I would have...

    That was always kinda my thoughy. I would have upped the size of the drier, especially since there was burnout
  7. Replies
    14
    Views
    443

    yep! Shootin from the hip more or less. I've...

    yep! Shootin from the hip more or less. I've never seen one but they don't seem that tricky. Not like a turbochef anyway
  8. Replies
    19
    Views
    1,129

    053 is all the bigger you go on a walk in? Seems...

    053 is all the bigger you go on a walk in? Seems small, would a 163 be overkill?
  9. Replies
    14
    Views
    443

    Possible, im wondering if one of the cycling...

    Possible, im wondering if one of the cycling valves is sticking open, from the way it looks its like a pizza oven that uses multiple valves, maybe one is sticking open.
  10. Replies
    14
    Views
    443

    508051

    508051
  11. Replies
    14
    Views
    443

    Yeah, 2 hi temp limits, 610 switch powers down...

    Yeah, 2 hi temp limits, 610 switch powers down everythig and boiler switch takes out ignition module
  12. Replies
    14
    Views
    443

    Does your main gas valve light stay lit? Just by...

    Does your main gas valve light stay lit? Just by looking at the wiring diagram (which is bad) it looks like there is a pilot relay that may be stuck. I would check continuity across some things when...
  13. Replies
    33
    Views
    1,444

    What was your liquid temp? With those numbers it...

    What was your liquid temp? With those numbers it may have been low and had a dirty condenser. Clean it even if it looks clean.
  14. Replies
    3
    Views
    296

    Ive had a few issues with switches as well, most...

    Ive had a few issues with switches as well, most notably the rocker style spdt square ones, put 3 in a plate warmer over the last 6 months. If im the next one to go back the new switch is gonna be...
  15. Replies
    1
    Views
    216

    With as much science thats in this field, you...

    With as much science thats in this field, you will never get labratory grade reading with field rated tools/instruments. Just the nature of the beast.
  16. Replies
    9
    Views
    423

    And people think im crazy when I pass on going...

    And people think im crazy when I pass on going out to eat at certain restaurants. Ignorance is bliss I guess.
  17. Replies
    12
    Views
    392

    Not quiet sure this is answering your question...

    Not quiet sure this is answering your question but here goes.
    You need the high potential (voltage) to make the spark. The higher the voltage the wider the spark can jump. Think water. Voltage is...
  18. Replies
    92
    Views
    4,200

    I only found a roll of moldy wire tape in an evap...

    I only found a roll of moldy wire tape in an evap pan.
  19. Replies
    7
    Views
    328

    I dont think the compression ratio would be...

    I dont think the compression ratio would be proper for it, you would need a pressure limiting valve and therefore possi ly restrict some suction cooling to it, stick with what the compressor is...
  20. Replies
    2
    Views
    220

    I have the pocket model. I dont do anything that...

    I have the pocket model. I dont do anything that needs labratory accuracy. I think its sufficient for comfort cooling in a residential application, nice and small with a decent sized tip to insert...
  21. Replies
    26
    Views
    1,124

    I think a big part also, is the fact that todays...

    I think a big part also, is the fact that todays systems are so much more advanced and delicate. Not saying that you shouldnt knock us newer guys cause we ask some fairly basic questions, I myself...
  22. Replies
    16
    Views
    480

    I see. Curious to know if you do a lot of...

    I see. Curious to know if you do a lot of hotside. Thats the area im most ambitious about. Most of our customers are restaurants and I do mainly the A/C and refr. Really wanna get into hotside...
  23. Replies
    16
    Views
    480

    I see, the last time I was at a McDonald's the...

    I see, the last time I was at a McDonald's the steamer they had was a garland. I havent been called to service the grill for any reason. What tools are involved with the certification? Is your...
  24. Replies
    16
    Views
    480

    what is this grill cert. you speak of? My company...

    what is this grill cert. you speak of? My company does 70% of the McDs in my area. never heard of grill cert. maybe I need to talk to my boss?

    Sent from my SCH-I545 using Tapatalk
  25. Replies
    16
    Views
    480

    ive always noticed they have a fairly extensive...

    ive always noticed they have a fairly extensive daily cleaning list for employees, maybe talk to the manager about getting that put on there, show them the tools they need and how its done. what was...
Results 1 to 25 of 225
Page 1 of 9 1 2 3 4
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event