Search:

Type: Posts; User: Warren

Search: Search took 0.00 seconds.

  1. Replies
    22
    Views
    1,701

    Only willing to buy one pound, would have been my...

    Only willing to buy one pound, would have been my que to walk away. When it didnt work is he going to expect you to come back for nothing to make it right?
  2. Replies
    6
    Views
    1,365

    The best thing to do would be to call Master...

    The best thing to do would be to call Master Bilt, and they should be able to help you. You want to CYA in case anybody gets trapped inside nobody will be able to say the factory was not made aware...
  3. Thread: T23G

    by Warren
    Replies
    2
    Views
    646

    When you get a chance, call True and ask if they...

    When you get a chance, call True and ask if they will send you their service manual. It covers cap tubes and alot of other info.
  4. Thread: Bad overload?

    by Warren
    Replies
    1
    Views
    710

    I have seen new units with a new overlod bad,...

    I have seen new units with a new overlod bad, jump it out while watching with your ampmeter and see how it runs. Had a new Hoshizaki with this problem.Also if temp control is out of whack and...
  5. Replies
    15
    Views
    2,493

    When Hoshizaki first came out with the flapper...

    When Hoshizaki first came out with the flapper type bin controls i got several calls where machines would not run when started up. The shipping tape was never taken off to let the flapper hang down....
  6. Replies
    43
    Views
    6,237

    How old is the time clock, i had a freezer that...

    How old is the time clock, i had a freezer that would freeze up and time clock checked out good. Froze up a couple of times eveything checked out good, finally found time clock would not advance...
  7. Are the fan delays wired in series so that both...

    Are the fan delays wired in series so that both have to warm up before overriding the time clock?
  8. Replies
    17
    Views
    1,847

    I just had one of these in the shop, dont...

    I just had one of these in the shop, dont remember any water splashing out. Have you checked to make sure inlet water valve is not leaking thru?
  9. Replies
    4
    Views
    1,124

    Call Stallings Ref in Charlotte NC 704 597 8480...

    Call Stallings Ref in Charlotte NC 704 597 8480 ask for June she may be able to help
  10. Replies
    2
    Views
    588

    Not as bad, you can get to this alot easier then...

    Not as bad, you can get to this alot easier then the eyes
  11. Replies
    4
    Views
    646

    You can go to their website and they have service...

    You can go to their website and they have service manuals.
  12. Replies
    2
    Views
    632

    Also clean the boot and run a brush thru the tube...

    Also clean the boot and run a brush thru the tube where the boot connects up to.
  13. Replies
    16
    Views
    2,195

    Does the board show that it has gone off on a...

    Does the board show that it has gone off on a safety? Also is the machine air or remote? If you are at the job call factory, they can really help you.
  14. Replies
    22
    Views
    3,954

    Manitowoc is using the same principle on their...

    Manitowoc is using the same principle on their quiet cube machines.
  15. Thread: AEA4440

    by Warren
    Replies
    3
    Views
    1,089

    Hope he doesnt tell them the condensor was dirty,...

    Hope he doesnt tell them the condensor was dirty, they will probably void the warranty.
  16. Thread: Door gasket

    by Warren
    Replies
    5
    Views
    867

    Call tech support at Manitowoc they can help you.

    Call tech support at Manitowoc they can help you.
  17. Replies
    7
    Views
    949

    Get them to give you the spec sheet for the unit....

    Get them to give you the spec sheet for the unit. It will have all the info on it. If it is a r12 unit it must have been sitting around along time and they havent been able to sell it. Why would you...
  18. Replies
    3
    Views
    2,627

    It's called CYA. Which means, cover your ( i'll...

    It's called CYA. Which means, cover your ( i'll let you guess the last word.)
  19. Replies
    12
    Views
    1,353

    Check and make sure the ground connection on the...

    Check and make sure the ground connection on the wire for circuit board is good and tight, that can make board do crazy things.
  20. Replies
    11
    Views
    1,095

    check the timer release solenoid on the back of...

    check the timer release solenoid on the back of the time clock, it may be burned which will not let clock go into defrost mode or make sure contacts make and break like they should
  21. Replies
    12
    Views
    5,665

    Actually you may be able to make some money in...

    Actually you may be able to make some money in the winter. Take the ice blocks off the condensing unit and sell them to the places in town that use ice blocks for ice sculptures.
Results 1 to 21 of 23
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event