Search:

Type: Posts; User: coppercliff

Page 1 of 2 1 2

Search: Search took 0.01 seconds.

  1. interesting I wish somebody had suggested that...

    interesting I wish somebody had suggested that to me before. I pulled my hair out for a while just like the op
  2. went through the exact same scenario. not with...

    went through the exact same scenario. not with propane though. the only part you didn't change may fix it, I replaced the burner itself. its a mesh burner and pretty tough to clean. doubt its the...
  3. Replies
    2
    Views
    303

    Thanks I will try them.

    Thanks I will try them.
  4. Replies
    2
    Views
    303

    trubovac vacuum packer

    Hello, does anyone know where I can get parts in North America for Turbovac machines? Thanks
  5. Replies
    5
    Views
    548

    interface pcb defective if all other components...

    interface pcb defective if all other components work if other componetns not working could be a fuse
  6. Replies
    5
    Views
    548

    do as badbozo suggested. to test in function...

    do as badbozo suggested. to test in function test, you have to first close the drain valve , then fill the drain box with the quenching solenoid so there is a reservoir of water for the cleanjet...
  7. Replies
    12
    Views
    736

    If its a "care control" unit and the rinse tabs...

    If its a "care control" unit and the rinse tabs are being used it should keep itself descaled. Having said that, yes I have seen it happen occasionaly but not often.
  8. Replies
    12
    Views
    736

    Did you try the battery reset? I work on a lot of...

    Did you try the battery reset? I work on a lot of these ovens, at this point I would do the battery reset as suggested by others. Also what software version is in it? I would also try updating the...
  9. That info would be great to have, thanks again

    That info would be great to have, thanks again
  10. the problem is probably pretty simple, and I...

    the problem is probably pretty simple, and I agree these are horrible. yes ive done an amp draw , the booster elements cycle off and on ok. the incoming hot water is definitely an issue. the hot...
  11. the fill and rinse is all the same line. its...

    the fill and rinse is all the same line. its possible that in the past the health inspectors have just been going by the temp gauges and just started using these strips. in other words it may have...
  12. no I am not entirely sure there is full water...

    no I am not entirely sure there is full water flow out of the rinse arms and those sound like good ideas to try. so your thinking the test strip the health inspector puts in there may not be getting...
  13. Also it is an electric booster. thanks

    Also it is an electric booster. thanks
  14. Thanks for the response. I am pretty confident my...

    Thanks for the response. I am pretty confident my temp probe is ac curate, I took the probe out of the booster tank and put it in a glass of hot water along with my probe, they both read the same....
  15. hobart H67e dishwasher rinse water not hot enough

    Hello, looked at this unit today because local health inspector telling customer actual rinse water temp inside cabinet is way too low. They use some kind of test strip they put in with the...
  16. Replies
    5
    Views
    503

    Its a fire waiting to happen I have condemned...

    Its a fire waiting to happen I have condemned many of these over the years for cracked frypots usually resulting in a fire. I would ask henny penny what they think about welding it
  17. Replies
    6
    Views
    418

    Start by dropping the planetary and checking the...

    Start by dropping the planetary and checking the gears in there.
  18. Replies
    4
    Views
    1,217

    They can get expensive, I have seen replacements...

    They can get expensive, I have seen replacements anywhere from 7 to 10 thousand dollars. If its allowed to do so in your state, nothing to lose by closing it up with a weld.
  19. Replies
    4
    Views
    1,217

    What is ther model number of the oven? depending...

    What is ther model number of the oven? depending on where you are located it may or may not be legal to weld it, I have seen it done, depends on the overall condition of the heat exchanger as well,...
  20. Replies
    13
    Views
    1,352

    Im not sure what you mean by low and high water...

    Im not sure what you mean by low and high water probes? I actually looked at a unit today for the same error, intermittent low water pressure . eo1.1. So the pressure gauge on the regulator assy...
  21. Replies
    13
    Views
    1,352

    hello, the error is coming from the pressure...

    hello, the error is coming from the pressure switch failing to close, look for a blockage at the screen at the triple solonoid inlet. I think you said this was an oes model, that should be a spritzer...
  22. Replies
    13
    Views
    1,352

    Ive worked on these off and on, all those things...

    Ive worked on these off and on, all those things ECTofix said need to be checked. As far as the descaling, most of the units i work on are boilerless, are you sure it has a boiler to descale? The low...
  23. Replies
    5
    Views
    1,178

    The new nut seems to have worked, thanks again

    The new nut seems to have worked, thanks again
  24. Replies
    5
    Views
    1,178

    Thanks again, dont have a local hobart dealer...

    Thanks again, dont have a local hobart dealer here as such, I will call Hobart parts and see if they will help me out, not being a dealer they are happy to sell parts but wont give any support...
  25. Replies
    5
    Views
    1,178

    wow, thanks for all the ideas. i assume the nut...

    wow, thanks for all the ideas. i assume the nut your talking about is the square lift nut. If i order this nut will i automatically get the new split version?
    Thanks again
Results 1 to 25 of 43
Page 1 of 2 1 2
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event