Search:

I was really hoping to get rid of the dreaded Red X. Maybe I will figure out a way to keep the controller powered in the winter.

Not really sure what everyone else uses for their campuses.

Any suggestions for a BacNet Weather station under $2000 or so?

We have a trane unit that we shut down for the winter and it goes offline. Is there any way to disable the offline result?

Thanks Man

My question is how do you network a CGE09090 to remotely communicate from a Bacnet Mstp trunk from the main building to a remote building over ethernet

We would like to remotely install a CGM09090 controller in another building and connect it through our network (BACnet protocol). I think you use a CGE type controller but that's about all I know.

There is one valid solution. Install a heat exchanger and pump. That way you can have glycol in your coil and prevent a lot of grief down the road.

We have a Delta inteliweb system with a DSC-1616E controller. I know the address of the computer. My question is where is the address for the controller on the network and how do you set it?

I need the plastic adaptors that basically a male 3/8' to female 1/2 " for conduit

Where can I get the plastic conduit conduit adaptors for the Grundfos pumps???

We have Patterson Kelly Boilers (Modbus) with Protonodes to convert to Bacnet. I can map the Protonode into Metays but cant discover any points. It seems like the communication between the boiler and...

Before we upgraded they took away Silverlight and our GGT Graphics stopped working. We have Metasys UI (MUI) and making graphics is pretty easy.

Is there any way to disable the offline x's when we have equipment shutdown for the season?

We don't have GGT Graphics. We have the MUI Graphics.

We just did an upgrade from Metasys MUI 11 to MUI 12. Now quite a few of graphics don't work. What happened?

Metasys 11, now we have Metasys 12.

Every time that our Network people perform an update and restart our Metasys server the SNE's go offline.
I know how to reconnect them. My question is there a fix for this issue.

I need to add some sensors to our system. I already have the sensors and was going to go with the 36P622 from Johnson Controls. Unfortunately they wanted $80.00 each. I just want something that can...

It was our IT department. The port our system was on was changed and it blocked the controller.

I have a Delta DSC-1616 and it will not come online. A few questions; 1. Does it have an Ethernet address 2. Is there a way to figure out the ethernet address 3. What does the red scan light mean...

The LCT program exists at the supervisory front end level.

You can accomplish a reset using LCT.

How do I tighten the temperature control up on these new controllers. Basically if the setpoint is 70 F, it sets cooling at 72 F and Heating at 68 F.

Back when I started with controls i would set up a trainer in my garage. Basically build a complete system and practice writing programs, graphics, and unique situations.

Are you still able to create a control system and use LCT?

What functionality do you lose with MUI. For example LCT etc...

Always utilize shielded cable and properly terminate the ground.

I would calibrate the thermostat to bring the heat valve on fully first, then fire the fan as sort of a second stage.

I'm going over to check that out today. Thanks

It causes the issue whether or not the network is plugged in.

Bacnet MS/TP Module

Pretty sure you have to purchase from Johnson Controls.

Having issues with a Bacnet communication module for a Daikin Microtech III (MT3006) . The original condition is the controller goes offline and basically shuts down the controller display. If we...

I think I found the issue. Although we were switching the occupancy switch BI of the UC800 on the Trane DX unit, the Occupancy BV point was not releasing. Apparently Metasys had take control of the...

LOM Lack of Maintenance
BFH Big F@%king Hammer

Have a Trane Unit with a UC800 BacNet Controller. The unit runs with the BAS occupancy switch open??? I can see the occupancy switch inside the controller switch with no impact on whether the unit...

My bad, didn't run as administrator!!!!

I get an alert when I try to access Johnson Controls CCT; Please select a different device, or a different connection point to access this device. What is causing this issue?

How do you lock out the setpoint on a NSB8BHN240-0 Network Thermostat.

I've actually put a AHU program into a UNT. It involved changing the type back to a UNT. I have the directions somewhere if you need them.

I looked at the computers that worked fine and the ones that freeze and there was one difference. The computers that freeze had Silverlight installed. I uninstalled Launcher and Silverlight. Then I...

The Metasys SMTP freezes when you try to load from computers on the Network. If I connect through the Network with my laptop it works just fine. It works just fine from the server (2012). It...

Curious to see where this project went and all. I worked at a Air Force Hospital with DCMs, which of course you cant take directly to NAE's. Against my advice they put in NIE's as integrators and...

Pretty much time to upgrade if you want to migrate to MUI

So I have a choice between ORCA View for Windows 10 and Intelliweb, we have a small system with about 120 points. Anyways I have a few questions. 1. Does Intelliweb support GCL+ programming? 2. Is...

Any issues with the upgrade?

Will the Delta Control System ORCAview 3.4 work with Windows 10 64 Bit?

Never mind I found the manual and suddenly my memory came back LOL

Was shown once a few years ago how to perform a back up. Can't quite figure out how to back up the system. Help