Search:

Type: Posts; User: neonhomer

Page 1 of 4 1 2 3 4

Search: Search took 0.01 seconds.

  1. 33CNTRANLON Lon Translator card XIF file

    Does anyone happen to have the XIF file for the Carrier Lon Translator card? I am unable to find it. I tried to extract one using NodeUtil, but it doesn't seem to work.



    File: CCNTOLON.XIF...
  2. Digging into the drive, it had been mis-wired *at...

    Digging into the drive, it had been mis-wired *at the drive*. Apparently, the installing electrician wired the controls to the drive directly instead of through the terminal blocks in the disconnect....
  3. Replies
    9
    Views
    690

    You can "upload" the controller database from the...

    You can "upload" the controller database from the controller, but you have to use WorkPlace Tech to do it. I'm not sure if the original contractor did this (we do it), but see if there is a CD or a...
  4. Altivar 31 VFD Not working w/ Start/Stop relay

    Have an existing Altivar 31 VFD. If you run though the parameters, and set Fun > Stc > Nst (Freewheel Stop via logic input) to LI2 (Where my start stop relay is landed), the drive will not run at...
  5. Replies
    25
    Views
    4,481

    I've made fuse "hacks" before, but I still used a...

    I've made fuse "hacks" before, but I still used a fuse... ie, I need a 5A blade fuse and only had a 5A glass fuse. It's the reason I carry a "fuse adapter" in my box. So I can convert from blade to...
  6. Replies
    12
    Views
    1,062

    The points are bring brought into my system as a...

    The points are bring brought into my system as a Analog Value.
  7. Replies
    12
    Views
    1,062

    "They will not stick" mean that when I set them,...

    "They will not stick" mean that when I set them, they will not write up to the controller.

    As for what level, I will have to see. I believe we are writing in at Lvl 10....
  8. Replies
    12
    Views
    1,062

    We have two points brought out: clg_setpt_1...

    We have two points brought out:

    clg_setpt_1
    htg_setpt_1

    The customer had an ALC tech come out and add these points in for us to control the system. According to him, this should be all we need...
  9. Replies
    12
    Views
    1,062

    I'm running into the same situation, except I am...

    I'm running into the same situation, except I am not using Niagara AX. I'm integrating a ALC WebCtrl 4.1 system into Schneider Electric's SmartStruxure. I have all the points I need to control the...
  10. Thread: BAS System

    by neonhomer
    Replies
    9
    Views
    1,321

    NiagaraAX should support any device that is...

    NiagaraAX should support any device that is Bacnet or Lonworks. It will also support the old Network 8000 stuff as well, but I believe it requires a special driver to do so.

    If you have an old...
  11. Was going to say it looks like a old Honeywell...

    Was going to say it looks like a old Honeywell system that was retrofitted to JCI. We just recently did a big retrofit at a hospital where it was a retrofit of a retrofit.. oh what fun....
  12. Replies
    24
    Views
    5,349

    Muffler tape FTW!

    Muffler tape FTW!
  13. Replies
    20
    Views
    4,621

    Not to bump a old thread, but could someone grace...

    Not to bump a old thread, but could someone grace me with a copy? Funny is that the Stryker graphics want the the file, but didn't come with the Stryker installer.
  14. With nviTodEvent, there is three points......

    With nviTodEvent, there is three points... currentstate, nextstate, and timetonextstate....

    I have the enum schedule linked to the nviTodEvent_currentState point, and the box seems to be...
  15. Honewell TR23 LED Blinking when VAV Overridden

    Controller is an Excel 10 W7751H, and the wall module is a TR23 w/ the Override button and LED. Front end is Niagara AX.

    When we send the boxes to unoccupied mode (by using the nviOccCmd), the LED...
  16. Replies
    20
    Views
    5,781

    Not all Honeywell Jaces will be tridium/niagara ...

    Not all Honeywell Jaces will be tridium/niagara

    But to answer the OP's original question, you can serial shell into the JACE and change the default platform username/password.
  17. I see NLUtil... from Newron systems... but it...

    I see NLUtil... from Newron systems... but it requires a login to get it... and there is no option for US....

    Anyone know anywhere else I can download it?

    Also.. found out why we had the...
  18. Tool to reset LON subnet/node/domain info

    We have a handful of LON VAV controllers that, due to a crappy network, failed commissioning through Niagara AX. We are looking for a program that we can run that will let us reset the LON...
  19. Try uninstalling and reinstalling the program....

    Try uninstalling and reinstalling the program. It's possible your license file is corrupted.

    If that doesn't work, then you might need to call in...
  20. Replies
    37
    Views
    12,070

    I've seen the big air handlers do that. Saw one...

    I've seen the big air handlers do that. Saw one in Miami in a brand new Trane M-Series... The wheel survived about a hour until it just imploded.

    Trane sent a completely new blower assembly out...
  21. Replies
    11
    Views
    2,553

    Holy underwear Batman! How many animals did they...

    Holy underwear Batman! How many animals did they have there?
  22. Replies
    0
    Views
    944

    Honeywell Microcell Controllers for VAV

    We have a bunch of old Microcell VAV controllers we pulled from a job. Looking to get rid of these things....
  23. Replies
    6
    Views
    1,177

    If you're tired of being spammed with the EPA...

    If you're tired of being spammed with the EPA message...

    https://community.niagara-central.com/ord?portal:/discussion/DiscussionThread/16972
  24. Replies
    3
    Views
    885

    I personally haven't tried it. I'm on Windows 7...

    I personally haven't tried it. I'm on Windows 7 with 5.8.6 without issues.

    I would imagine if you use a 32-bit version of Windows 7, and the latest version of 4.0 (that you are allowed to use), it...
  25. Replies
    24
    Views
    6,394

    Must be nice to have a van... As a controls guy,...

    Must be nice to have a van... As a controls guy, I am driving a little Nissan Versa hatchback... What's worse is that the paint is fading, and it's white to boot! I try to keep it clean, but the...
  26. Replies
    27
    Views
    8,444

    I don't do refrigeration professionally (I'm a...

    I don't do refrigeration professionally (I'm a controls guy), but even I can unbolt a contactor from a unit to make the wiring connection if it is a bit too tight...

    On a side note, I replaced a...
  27. Replies
    3
    Views
    885

    Without a prompt for what? If you don't...

    Without a prompt for what? If you don't register/license WPT, it will nag you every time you start it. No way around it.

    Best thing to do is either upgrade to WPT (The latest being 5.8.6), or keep...
  28. Replies
    4
    Views
    1,431

    Swapped sub-bases... Temp still jumps around. ...

    Swapped sub-bases... Temp still jumps around.

    Only thing I can think of now is that maybe the wire is bad, or it is picking up noise,.,..,.,
  29. Replies
    4
    Views
    1,431

    Honeywell T7350 Temperature jumps around

    If you're wondering, it's the same job...

    A Honeywell T7350 tstat with the remote TR21-H Temp/Humidity sensor... The original complaint was the temperature was jumping around by 3-5 degrees, and...
  30. Replies
    5
    Views
    1,828

    If you want to get rid of that stat... You can...

    If you want to get rid of that stat... You can send it my way. I am looking for one to hang on to for a spare....
  31. Replies
    46
    Views
    11,206

    Would this module be found in the SoftJACE...

    Would this module be found in the SoftJACE download from NiagaraCentral? I am using TAC's version of AX, and a station I am working on is screaming about needing the VykonPro module....
  32. Replies
    0
    Views
    713

    WTB: ENC-420 or 520

    I am looking for a used ENC 520 or 420 to play around with. Maybe you have one that has a bad port, or something like that. Maybe one that needs recapped, or needs a new xfmr or the like.

    I am...
  33. Thread: i'm 98%

    by neonhomer
    Replies
    157
    Views
    40,917

    2% - Blue strippers (wire, people)

    2% - Blue strippers (wire, people)
  34. Replies
    28
    Views
    4,772

    When I had my interview for my controls...

    When I had my interview for my controls technician position, I wore a polo shirt, and non-faded pair of cargo pants, and a non-marked up pair of "duty boots" (black police boots, similar to army...
  35. Replies
    5
    Views
    1,828

    For anyone who was following... I ended up having...

    For anyone who was following... I ended up having to re-commission the stats. With just one, I pulled in all my points, configured them, and put in my setpoints. I then copied them to the other...
  36. Replies
    5
    Views
    1,828

    Hmmm... I am not using the standby cool/heat...

    Hmmm... I am not using the standby cool/heat setpoints...
  37. Replies
    5
    Views
    1,828

    Honeywell T7350 Lon stats and Niagara AX

    Grumble... Trying to set the Occupied/Unoccupied Heat/Cool setpoints from inside AX on these stats. When you try to do it through the nciSetpoint_occupiedCool (or the other four), the stat does not...
  38. Replies
    7
    Views
    1,654

    I was able to get out on a job and hook up. I can...

    I was able to get out on a job and hook up. I can communicate with a controller, but I still get the 1068 error.

    From what I have been reading, I guess I need the 8.08b update.
    ...
  39. Replies
    7
    Views
    1,654

    Okay. I figured out what was hogging my Com1...

    Okay. I figured out what was hogging my Com1 port. I have the USB - serial adapter hooked up to the CVTPRO300 box. I fire up HVACPRO, and try to pull up anything to see if the adapter is talking to...
  40. Replies
    7
    Views
    1,654

    Now I have to figure out what the heck is hogging...

    Now I have to figure out what the heck is hogging up my Com1 or Com2 port. Sometimes I hate Windows XP....
  41. Thread: Trane Summit

    by neonhomer
    Replies
    5
    Views
    1,162

    I know what you mean... not to go too far OT, but...

    I know what you mean... not to go too far OT, but I hate typing on a touchscreen device... that's why I love my BlackBerry.....

    I think it would be awesome if Trane released older versions of...
  42. Thread: Trane Summit

    by neonhomer
    Replies
    5
    Views
    1,162

    HUH? I have reprogrammed Comm5 AHU...

    HUH? I have reprogrammed Comm5 AHU controller's with Rover before, writing in routines and points to allow for O/A calibration, O/A Damper tracking, etc etc.



    However, Rover will not allow...
  43. Replies
    7
    Views
    1,654

    1400's I think.... I am not entirely sure....

    1400's I think.... I am not entirely sure....
  44. Replies
    7
    Views
    1,654

    Johnson balancing software

    Well, my new employer handed me one of these....

    http://airbalancestore.com/images/D/AS-CVTPRO300-1.jpg

    I need to find the Windows based VAV software for these... I have the Palm software and...
  45. Replies
    8
    Views
    2,213

    chillrdude, you have PM....

    chillrdude, you have PM....
  46. Replies
    8
    Views
    2,213

    Lemme look on my laptop when I get home. I...

    Lemme look on my laptop when I get home. I believe I have SP10 for ver 5...
  47. Old topic, different spin, and different...

    Old topic, different spin, and different employer!!

    I need the Johnson Controls PC balancing software. I have the Metasys box that goes from a serial port on my computer to a stat. It came with a...
  48. Replies
    8
    Views
    3,200

    The copy of WPT I have was licensed to me by a...

    The copy of WPT I have was licensed to me by a local TAC dealer. You might be able to contact TAC and they might be able to get you a copy of it on an academic basis if you prove your need.
  49. Replies
    4
    Views
    719

    Usually, Trane will only sell the Comm4 Service...

    Usually, Trane will only sell the Comm4 Service tool and Lon Air & Water balance tool. I was able to get the full monty, but it was a screw up. The only thing I know to do is to get the proper part...
  50. Replies
    1
    Views
    606

    KMC T&B Software

    Does anyone know where I can get the TAB software for KMC? We have a few laptops with the Wincontrol software on it, but they are older systems due for replacement. We need to be able to reinstall it...
Results 1 to 50 of 199
Page 1 of 4 1 2 3 4

Related Forums

Plumbing Talks | Contractor MagazineThe place where Electrical professionals meet.
Comfortech 365