Search:

Hi ControlTec,
Thank you for the reply I am really looking for a PEM1 programers manual and a GCM programers manual.I appreciate the feedback and yes I am using the infocon driver.I can see all the...

Can anyone help me out here?

Hi everyone,
I too have a Network 8000 system and need to make changes as the GCM is being replaced with a Jace.I have discovered the PEM's and the MZ11 checked the logic blocks in the GCM with...

Sit down with a cup of joe and read up on your states and other things like saturation timers etc and then do as proxyking says disable prac and check your propbands.
GB

Like i said contact me via my Email my office is located in Metro Boston Area.
GB

Very experienced wth PMI NCM GPL JCBASIC contact info in my profile

After a recent power failure we cant log on with any of the user ID's. Is there a default password for XBS 1.4.3? My email addy is in my profile if you can help us that would be great.

You could send the N30 out to be repaired or install a Tridium style supervisory FX20 would work just fine for you.

Thank You everyone that did the trick although the DWU was set below the Occupied Heating setpoint they may have been set to closely together.
In addition patience is the key it took a long time for...

I appreciate the help and yes I have been to the FX Supervisory Control training class couple years ago but they did not cover the server setup in great detail. I have looked into the AX...

Hi,
What rev PMI and GPL are you running and on what kinda computer is that XP machine there spanky?
Shutdown PMI and launch GPL from the FMS/BIN directory. I dont think GPL was ever tested on XP...

The last one i ordered from JCI this past Summer had a lead time of 8 weeks. Try Ebay buy an old NCM 350 and use the power supply.

GB

I thank you all for your help I will be on site later this week and will try the setpoint and review the sequence of operation.Its getting cold up here in the NE :) good for business.

GB

I have a question on the alarm portal.My Niagara Network is all setup three FX's all see each other and the server.I setup a station recipient for each FX pointing to the server but my alarms are not...

Hi Mark,
Yes I tried that yesterday and the gas heat stages on normally in test mode.The only recent issue with the unit has been the static pressure has been reading hi I am waiting on a altivar...

Hi,
I have a problem with a Trane Intellipak.The unit wont stage the gas burner on the heat mode enables but the heat does not stage on.All the temperature sensors are reading ok.I put the unit in...

Setup M-Trend for the points you need to trend when you want to archive your trend data simply look for the Trenddb.mdb file in the Mdata or active database subdirectory and copy a blank Trenddb.mdb...

Go the Niagara route AX of FX especially if your GPL for the DCM's is complex.The programing capability on the AX/FX is vastly superior to the Extended Architecture product line.
GB

Wow that Sam I must ask thread has legs anyways onto your question try this...


To reset and set up M-Password:

1) Select Start > Programs > JCI > M-Password > Config. Leave User Name blank...

Do you have a occupied BD point? Just curious why you are scheduling the fan command itself and not the occupied command.You could also schedule the shutdown command BD 197 if need be. Any chance...

What point are you scheduling?

I will assume you have a NCM 350.Did you check your Novram in the NCM kinda curious as to what port the modem is assigned to.What type code general with OT or NT use NT when you have a modem assigned...

That sounds like a normal power up sequence for the N30. Leave it alone is my advice we have had several fail downloads and go into boot code conditions or worse for no reason at all. Time to upgrade...

Is the DS2 red led on steady or flashing? Does the controller reset continuously?

GB

If you rule out the sensor and connections it sounds as though the only thing left is the wire. I will assume the sensor has worked correctly in the past.Is the sensor mounted in a short penetration...