Search:

We just Had our T&S Rep tell our office that it is against most codes to reuse a gas line or fitting..
I know Gasquip or Gas/flex fittings are single use but Quick disconnects? Really?

Lets here from some of the old schoolers that would remember some old brands that were out there in the 60s , 70s & 80s

I have a few
Koch 1969-1979
Kold draft ( Original 1975)
Hobart (1968)...

Have you completed a Water volume test ?
Line from after solinoid into a 5 gal bucket test it for 60 seconds then measure water in Bucket.

Yup 100% its gotta be exact.. the timingband wash as well as fill and refill has to be exact..they did it so there is no short cutting.. Taylor freezer put a time delay open circuit so one has to...

Ive found this to be just the opposite they are all flimsey for sure but ive never broke one off.. the trick to Danfoss brazing ... heat the pipe not the valve side the brazepoint isnt the outside of...

Poo head... This is a Medium Temp Application 35Deg Box 27 degree Evap.. Beer No defrost needed..

Yes exist gas was R404a Yes back in the day the fins were thicker and spaced further apart. But pretty much across the board for economic reasons most mfgs use the same coil for both . Here in...

I remember those Bristol rattle bucket Compressors back in the early 2000s Manitowoc would put insulation wraps on them to quiet them down then after they realized Bristol cheaped out on the paint...

That sounds like a board issue..if the harvest light and ITP light is off that's a bad board in my book . I keep a spare just to test in these situations

Like others said Actuater ruptured you can replace just the diaphragm. Always fails to heat mode.

Higher back pressure was the reason converting the compressor to med temp. The Evap is the same coil as in medium temp application less the "Z"Valve and electric defrost. My main question was same...

Box is 6x8 Evap is a Bohn 9600btu 2 fan went with a 12,200 btu compressor medium temp

We have a customer That is taking a freezer and turning it into a Cooler The condenser is new and My question is The TXV is R-404 can I just replace the Compressor and the TXV Head?

Hey if Its a 2912-c there are two Allens to remove one on Bearing Bridge and other under Sharpening Assy.
Remove ,Knife, Pulley, Belt, Set screws (2) then Use a Block of wood and Beat out Knife end...

1 defrost Clock 1 thermostat To keep from Slaving
I hate cooltubes...

The ole "FUn"

Why not just do What we did and Use a Braze plate? And PVC Feed

Who Is with me on these Damn Digital Controllers?
New service call on a T23F Controller reading E1 Pushed buttons looked up online to no avail, Called True The Service tech said E1 is bad...

This unit wasn't installed by us it was installed in 2007 . Trane says its length of run is okay .
However... Upon getting into it this Morning we found a second drier "Above the Ceiling" CRAZY!!!!...

We have a Trane TTR120A Condenser 480/3 with 71 foot Vertical Run with 3 P-traps We had a Low charge condition but system would not fill to a full column of liquid. We removed the Refrigerant Scaled...

I understand Completely BUT... The refrigeration Has to be Up sized. We recently did a Blast chiller for Einsteins Bagels and it was a 6x12 Walk in with 61,000 btu's of cooling.. with Defrost and...

I used to keep 1/8" Dull stainless bits in a pill bottle they make great stops.. When the spring is Popped inside the Door The only Fix is to replace .. Very easy Swap

Many of our continual calls are because customers are putting prep right from stovetop into cooler.. Our Health Dept allows 2 hours of ambient cooling before needing to be refrigerated.how many times...

Kold-pak has the best Fastest box for standard sizing they have a fast ship box that can ship in 2 days . IMO American panel makes the best box..

Wow you should be outed..you don't belong on this forum...

Really Dumb Call on Saturday...
Customer called our dispatch and said my cooler is at 70 degrees and I lost everything overnight. So I rush there (40 min) I get there and Open the door the fans were...

I know I get that BUT.... I know the use of a blast chiller.I know the best way is to cool immediately. But if the State Health Dept says you have 2 hours then I think they know a little about food...

Here in Georgia our health department allows any type of food being protein or vegetable a cool down period of two hours in The ambient temperature of the kitchen .Then can be rolled in at 80 degrees...

I have a very Stubborn Customer that Insists on telling all of its Stores (34) that instruct your kitchen Prep as soon as the food stops steaming its okay
to put in the cooler. Its a new Owner with...

My Last one was A neighbor asked me to look at their AC it had been off for days. Went to the Condenser and opened it up and found it had power but no 24 volt feed from Furnace?
no where to be...

all Our trucks Have 24 footers on them I agree 24 foot gets to 90% of roofs

About the only thing I like about the indigo series is it hold Fault codes and shows how many ice cycles total.
I would say WLP water Level probe could be dirty or Leaky water valve keeping probe...

First Off You dont Install Fan cycle with a Head master....
Looks like possible txv Flood?
Did you weigh in a charge?

I agree a lot of techs insist on the cheapness of harbor freight and Northern tool but not on a service truck. Rothenburger compact kit goes up to 1"1/4
and is quite the heavy duty electric threader

I believe You will succed

This .....

Nice Install Youll be sorry with the Quietcube.... Keep them Clean And Put filters on them!

Black max or hillmore in my opinion is the best I love my Black max!!

RUN!!

Hoshizaki All day and 3 times on Sunday Not only are we a Rep for Hoshi their in our back yard Ive been to the plant many many times Its just made better and the care they take to make sure they are...

Terry Is correct 139-142 is correct....

We have used Disco since 2008 and is very easy to use

Freezer Heads are designed to hold in a -40 Degree Ambient...if in a fluctuation type enviro should be a Gas system \
Ive seen Idiots pipe a system straight from cooler compartment to Freezer...

I would do a pump down test for a weak compressor or maybe bypassing? Then Zero the TXV then scale you in a charge. Ive also suspected Mixed refrigerants before on a freezer evap that wont pull down .

Yup but even Dupont dont call it Freon.,and its written on no bottle or tank anywhere any longer. Also it was for Freon -12 how many AC systems residential you know operate on R-12?

The liquid line Looks too small?

Most New Units Lennox,Carrier,Trane,ICP have a designated place to Mount Disconnect and the Electricians STILL mount them where they want...Its Not a Suggestion!!

I Must say itsiceman and iceman I have been on here for awhile,I understand your contrabution.. I can retract my post about you guys not being stand up enough to actually
Answer in anything other...

Just asking but what part of the bearings and seals and a scored evaporator is going to have anything todo with the txv? Flooding?

We Kept a Bag of Zip ties used to tie a AAON control door closed .
kept them inside so when you cut the old one off just zip tie another on where someone locked the lock and we had to drill out the...