Search:

Type: Posts; User: CM3Tech

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    5
    Views
    1,337

    CSI, My quick thoughts would be the obvious: ...

    CSI,

    My quick thoughts would be the obvious:
    Do a learn NVs on the object (dynamic device)
    Do an upload
    Do a fetch
    Commission
    Link the binding
    If that does not do it I suggest...
  2. Replies
    20
    Views
    1,250

    Modbus to Lon Convertor?

    Hey Gents,

    Here is what I am running into with no experience with this Convertor.

    A Thermax Chiller was supposed to be supplied with Lon Cards for me to integrate with. The factory tech in...
  3. Replies
    0
    Views
    922

    Thermax Absorption Chillers??

    Has anyone worked with these Thermax Absorption Chillers before. I have 2 schools with 2 each. Alot of the points like start/stops, etc. are self explanatory. However there are certain points that...
  4. Replies
    34
    Views
    1,732

    Tony, You are looking for the button in the...

    Tony,

    You are looking for the button in the toolbar on top that looks like a thumbtack. It is the fourth button in from the left. It sounds like your button should be pressed and gray. If you...
  5. If you can get pinned from the device to your...

    If you can get pinned from the device to your computer , if that is correct, it be would apparent your Lon Card is functioning correctly.

    I will take it you are a new user too WPT. It can be a...
  6. Replies
    7
    Views
    2,433

    From my limited experience with the Trane BCU, ...

    From my limited experience with the Trane BCU, if you have access to the Summit software. I believe you can find it in there some where or use the ipconfig software that they use to setup the IP. ...
  7. Thread: Need advice???

    by CM3Tech
    Replies
    1
    Views
    468

    Need advice???

    Here is my situation, the company I work for is going to be getting a job integrateing an existing Siemens system with a TAC UNC or JACE( or whatever else it is called out there). It isn't as much...
  8. Replies
    12
    Views
    1,872

    Dutchman, Good thread something I do not think...

    Dutchman,

    Good thread something I do not think or run into ever. I do know of one town/campus that as recently started a large district chiller plant. That is Penn State University Main Campus...
  9. Replies
    4
    Views
    886

    scrooloose, The trane tech was out and setup...

    scrooloose,

    The trane tech was out and setup the I/O in for me and I got a list of what the instance number or device IDs are.

    I have another question concerning the BACnet/Ethernet. Now...
  10. Replies
    4
    Views
    886

    Trane BCU to Tridium

    I need the advice from a knowledgable Trane tech. I am currently attempting to integrate with a Trance BCU via BACnet. I have been looking all over this and a few other sites to get some info on...
  11. Replies
    3
    Views
    500

    Landis & Staefa 540-400

    Ran into a couple of these older controllers. They have two pneumatic outputs with the gauges in front. Wondering if anyone has a manual or cut-sheet of these? The application they are running is...
  12. Replies
    19
    Views
    2,181

    At the site I am working at I have two DCU's one...

    At the site I am working at I have two DCU's one has all the controls on the comm loop and the other has nothing on it. Each DCU has the DXC, the expansion card to ethernet. Each ethernet card is...
  13. Replies
    19
    Views
    2,181

    orcaview, Is it as easy as changing the comm...

    orcaview,

    Is it as easy as changing the comm board? I can not imagen it being that easy.
  14. Replies
    19
    Views
    2,181

    Delta Controls: V2 to BACnet

    Is there anyway of changing a V2 comm loop to a BACnet comm loop??



    I am/was supposed to be integrating with Delta controllers that I was told were BACnet, come to find out these are the older...
  15. Replies
    12
    Views
    838

    That would be the one. Who are you with griff?

    That would be the one. Who are you with griff?
  16. Replies
    12
    Views
    838

    Rleo, I have never used HVAC Pro before, but...

    Rleo,

    I have never used HVAC Pro before, but it seems that your analog output is reversed. When you want 100% heat it outputs 0 volts and when you want 0% or no heat the controller should output...
  17. Replies
    134
    Views
    26,484

    Does anyone have the software that is used with a...

    Does anyone have the software that is used with a UC?
  18. Replies
    12
    Views
    1,357

    I like that thought pattern, Nikko. I am fairly...

    I like that thought pattern, Nikko. I am fairly new in the field and a young guy. I can easy get caught up in the thought pattern the newest and flashest (wireless) has to be the best; until...
  19. I did not know about getting a replacement while...

    I did not know about getting a replacement while the one that is down is being repaired. I would suppose the decision would be between the price & time of the software and reloading or the price of...
  20. Yes that is correct Work Place Pro would do a...

    Yes that is correct Work Place Pro would do a soft start of the UNC. I am not sure of the price of WPP I just get it as a tech, but I will ask around and see if I can get a number.

    I have only...
  21. If you are talking completely failed as in will...

    If you are talking completely failed as in will not work after a re-boot that is a mighty expensive replacement. If you have not tried the re-boot I would recommend it, a good restart many be all...
  22. Replies
    0
    Views
    464

    TAC UNC integrating with Delta Controls

    I have a TAC UNC at the job site with Tridium framework. I am integrating that with a Delta System. The Delta system is a DOW 322 version with about 12-15 different controllers. Everything from...
  23. Replies
    1
    Views
    475

    Siemens App 2281

    Does anyone have a file for application 2281. It's a TEC app for UV's.

    Thanks
  24. Replies
    13
    Views
    1,426

    Thanks guys, That sounds like a good solution...

    Thanks guys,

    That sounds like a good solution to me. I will try it after the holiday when I get back to the sight. I new that it was a glitch in the system. That is why I love this site. The...
  25. Replies
    13
    Views
    1,426

    Big Johnson I will try changing it to a...

    Big Johnson

    I will try changing it to a virtual point and let you know how that goes. I will not be there till after the new year.

    A question for you is how would I go about clearing the...
Results 1 to 25 of 33
Page 1 of 2 1 2
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event