Search Results - HVAC-Talk: Heating, Air & Refrigeration Discussion

Search:

Type: Posts; User: Cosmicmuffin

Page 1 of 9 1 2 3 4

Search: Search took 0.01 seconds.

  1. I think the "guest" is referring to pulling...

    I think the "guest" is referring to pulling refrigerant back into the comp. Not pulling a vacuum before "setting" proper charge. My question,why are you doing this on "new' units?
  2. Replies
    13
    Views
    500

    Very good. Was there a piston attached to the...

    Very good. Was there a piston attached to the condenser? Thats the one to use,if not,double check charts.quessing about a .055.
    Pressure look pretty good to me,
  3. Replies
    16
    Views
    496

    I believe the E.R. uses liquid cocaine to re...

    I believe the E.R. uses liquid cocaine to re leave pain. Obviously not available over the counter!
  4. How do you check the pressures with both service...

    How do you check the pressures with both service ports closed?
  5. Replies
    6
    Views
    386

    And why didnt you try to warranty it? seems like...

    And why didnt you try to warranty it? seems like alot of work. We all know who's going to eat that!
  6. Replies
    5
    Views
    680

    Was out on routine service.Goodman GMS,this is...

    Was out on routine service.Goodman GMS,this is single stage nat gas,hi eff. (sorry no Mod&Ser). First thing I noticed was,plate in front of burner brown in color,more burnt look than rust. Visually...
  7. Replies
    33
    Views
    1,635

    [QUOTE=Af7171;18116211]Tech who do side work can...

    [QUOTE=Af7171;18116211]Tech who do side work can do it a lot cheaper .they use the company truck and company stock . No overhead . It all profit .

    Your correct there! We had a large HVAC Co....
  8. Replies
    33
    Views
    1,635

    A very prosperous salesmen once told me,If your...

    A very prosperous salesmen once told me,If your getting every job you bid,add 20%.,If work slows down,adjust accordingly!
  9. Replies
    22
    Views
    1,121

    Did I miss something?

    Did I miss something?
  10. Replies
    44
    Views
    11,631

    The "cleaning" property's of R410A are so much...

    The "cleaning" property's of R410A are so much better than say R22,. Been told by Reps. if you cut lines open down the road,there crystal clean! You know where it went?
  11. Replies
    19
    Views
    671

    Tip; Remove hi limit switch,take supply reading...

    Tip; Remove hi limit switch,take supply reading there.also take heat rise temp test.
  12. Replies
    14
    Views
    1,138

    Ditto; Goodman made a good move there!

    Ditto; Goodman made a good move there!
  13. Replies
    2
    Views
    281

    SALON...,have been told,chemical used in these...

    SALON...,have been told,chemical used in these place raise havoc with H.X etc! Bet the mechanical room is used to store them. Did have roofers once push chimney cap down,almost completely shut....
  14. Replies
    5
    Views
    429

    Yes the pilot did appear to be high,however they...

    Yes the pilot did appear to be high,however they have a heatshield above it,and cover.(could you even adjust it?) I did run my camera in to burner access,up to first bend,no holes. I did do a heat...
  15. Replies
    5
    Views
    429

    HEIL HELP NEEDED !

    Have an older Heil,condensating furnace. Msd NTGM100EHA3 Ser. L983817999 It keeps tripping roll-out switch,which I have replaced,that is attached to the closed combustion burner box.Box does appear...
  16. Replies
    29
    Views
    1,492

    Hows that work with "stand pipes" in cyl. tanks?

    Hows that work with "stand pipes" in cyl. tanks?
  17. Replies
    27
    Views
    1,609

    Had this same problem after replacing HSI with a...

    Had this same problem after replacing HSI with a retro fit. Lost seal in combustion air box,swirling air would not allow to light. Resealed with silicone,worked fine. Original HSI should have been...
  18. Replies
    36
    Views
    1,404

    Dido's....,7 cracks,one of the clam shells was...

    Dido's....,7 cracks,one of the clam shells was completely rusted off at face plate. Customer said the "click-it" switch was bad,he bypassed it. Was a roll-out switch. Cant fix stupid!
  19. Replies
    9
    Views
    865

    Traps can fool ya,by the time you get there,a...

    Traps can fool ya,by the time you get there,a partial blockage in trap will drain down. Will work fine when you reset the lock out.,then starts backing up water later when you've left. Clean em!
  20. Replies
    35
    Views
    1,843

    Did you clean orfice in pilot! Did one other...

    Did you clean orfice in pilot! Did one other day,the smallest "broach" they make bearly fits. Flame doubled in size afterwards! Yes...,they can be a ***** to get out! Sorry to bust up movie review.
  21. Replies
    32
    Views
    1,220

    Our electric suppliers give up to $450 rebate for...

    Our electric suppliers give up to $450 rebate for higher seer ratings.I then take half of that away on bid,for doing all the paperwork B.S.
  22. Flattin out those small "duct hangers" and zip...

    Flattin out those small "duct hangers" and zip screws,after a bead of silicone. Anglehead screwgun helps.
  23. Ok...,I'll bite. What the difference?

    Ok...,I'll bite. What the difference?
  24. Replies
    5
    Views
    680

    INSHOT BURNER NOISE ?

    Was out on routine service.Goodman GMS,this is single stage nat gas,hi eff. (sorry no Mod&Ser). First thing I noticed was,plate in front of burner brown in color,more burnt look than rust. Visually...
  25. Replies
    9
    Views
    940

    COMPANY OWNER CANT SHUT UP !

    I and other, subcontract ourselves to a supplier to do both installs and service,"we are not employees". He has a well established business,and does count for a good part of are annual income.As most...
Results 1 to 25 of 218
Page 1 of 9 1 2 3 4
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event